BORDER SECURITY USING WIRELESS INTEGRATED NETWORK SENSORS (WINS)
Thread Rating:
  • 2 Vote(s) - 3 Average
  • 1
  • 2
  • 3
  • 4
  • 5
computer science crazy
Super Moderator
******

Posts: 3,048
Joined: Dec 2008
#1
03-09-2009, 04:22 PM


Wireless Integrated Network Sensors (WINS) now provide a new monitoring and control capability for monitoring the borders of the country. Using this concept we can easily identify a stranger or some terrorists entering the border.

The border area is divided into number of nodes. Each node is in contact with each other and with the main node. The noise produced by the foot-steps of the stranger are collected using the sensor. This sensed signal is then converted into power spectral density and the compared with reference value of our convenience. Accordingly the compared value is processed using a microprocessor, which sends appropriate signals to the main node. Thus the stranger is identified at the main node.

A series of interface, signal processing, and communication systems have been implemented in micro power CMOS circuits. A micro power spectrum analyzer has been developed to enable low power operation of the entire WINS system.
Use Search at http://topicideas.net/search.php wisely To Get Information About Project Topic and Seminar ideas with report/source code along pdf and ppt presenaion
Reply
computer science technology
Active In SP
**

Posts: 740
Joined: Jan 2010
#2
27-01-2010, 08:43 PM


.pdf   border-security-using-wireless-integrated-network-sensor-by-vinay-kumar-IPEC.pdf (Size: 439.85 KB / Downloads: 1,574)

Wireless Integrated Network Sensors (WINS) provide distributed network and Internet access to sensors, controls, and processors that are deeply embedded in equipment, facilities, and the environment. The Wireless Integrated Network Sensors (WINS) network is a new monitoring and control capability for applications intransportation, manufacturing, health care, environmental monitoring, and safety and security,border security. Wireless Integrated Network Sensors WINS networks provide sensing, local control, and embedded intelligent systems in structures, materials, and environments Wireless Integrated Network Sensors combine microsensor technology, low power signal processing, low power computation, and low power, low cost wireless networking capability in a compact system..

and read
reference.kfupm.edu.sa/content/w/i/wireless_integrated_network_sensors__low_6053.pdf
seminar and presentationproject and implimentationsattachment.php?aid=736
Use Search at http://topicideas.net/search.php wisely To Get Information About Project Topic and Seminar ideas with report/source code along pdf and ppt presenaion
Reply
project report tiger
Active In SP
**

Posts: 1,062
Joined: Feb 2010
#3
02-02-2010, 01:23 PM


.doc   border security using wireless integrated network sensors.doc (Size: 189 KB / Downloads: 1,166)

.pdf   border-security-using-wireless-integrated-network-sensor.pdf (Size: 439.85 KB / Downloads: 1,263)

.ppt   Border-Security-Using-Wireless-Integrated-Network-Sensor-Seminar presentation.ppt (Size: 1.95 MB / Downloads: 1,831)

ABSTRACT
Wireless Integrated Network Sensors (WINS) now provide a new monitoring and control capability for monitoring the borders of the country. Using this concept we can easily identify a stranger or some terrorists entering the border. The border area is divided into number of nodes. Each node is in contact with each other and with the main node. The noise produced by the foot-steps of the stranger are collected using the sensor. This sensed signal is then converted into power spectral density and the compared with reference value of our convenience. Accordingly the compared value is processed using a microprocessor, which sends appropriate signals to the main node. Thus the stranger is identified at the main node. A series of interface, signal processing, and communication systems have been implemented in micro power CMOS circuits. A micro power spectrum analyzer has been developed to enable low power operation of the entire WINS system.
Thus WINS require a Microwatt of power. But it is very cheaper when compared to other security systems such as RADAR under use. It is even used for short distance communication less than 1 Km. It produces a less amount of delay. Hence it is reasonably faster. On a global scale, WINS will permit monitoring of land, water, and air resources for environmental monitoring. On a national scale, transportation systems, and borders will be monitored for efficiency, safety, and security.
BORDER SECURITY USING
WIRELESS INTEGRATED NETWORK SENSORS (WINS)
1. INTRODUCTION
Wireless Integrated Network Sensors (WINS) combine sensing, signal processing, decision capability, and wireless networking capability in a compact, low power system. Compact geometry and low cost allows WINS to be embedded and distributed at a small fraction of the cost of conventional wireline sensor and actuator systems. On a local, wide-area scale, battlefield situational awareness will provide personnel health monitoring and enhance security and efficiency. Also, on a metropolitan scale, new traffic, security, emergency, and disaster recovery services will be enabled by WINS. On a local, enterprise scale, WINS will create a manufacturing information service for cost and quality control. The opportunities for WINS depend on the development of scalable, low cost, sensor network architecture. This requires that sensor information be conveyed to the user at low bit rate with low power transceivers. Continuous sensor signal processing must be provided to enable constant monitoring of events in an environment. Distributed signal processing and decision making enable events to be identified at the remote sensor. Thus, information in the form of decisions is conveyed in short message packets. Future applications of distributed embedded processors and sensors will require massive numbers of devices. In this paper we have concentrated in the most important application, Border Security.
2. WINS SYSTEM ARCHITECTURE
Conventional wireless networks are supported by complex protocols that are developed for voice and data transmission for handhelds and mobile terminals. These networks are also developed to support communication over long range (up to 1km or more) with link bit rate over 100kbps. In contrast to conventional wireless networks, the WINS network must support large numbers of sensors in a local area with short range and low average bit rate communication (less than 1kbps). The network design must consider the requirement to service dense sensor distributions with an emphasis on recovering environment information. Multihop communication yields large power and scalability advantages for WINS networks. Multihop communication, therefore, provides an immediate advance in capability for the WINS narrow Bandwidth devices. However, WINS Multihop Communication networks permit large power reduction and the implementation of dense node distribution. The multihop communication has been shown in the figure 2. The figure 1 represents the general structure of the wireless integrated network sensors (WINS) arrangement.
Continuous operation low duty cycle
Figure 1. The wireless integrated network sensor (WINS) architecture.
3. WINS NODE ARCHITECTURE
The WINS node architecture (Figure 1) is developed to enable continuous sensing, event detection, and event identification at low power. Since the event detection process must occur continuously, the sensor, data converter, data buffer, and spectrum analyzer must all operate at micro power levels. In the event that an event is detected, the spectrum analyzer output may trigger the microcontroller. The microcontroller may then issue commands for additional signal processing operations for identification of the event signal. Protocols for node operation then determine whether a remote user or neighboring WINS node should be alerted. The WINS node then supplies an attribute of the identified event, for example, the address of the event in an event look-up-table stored in all network nodes. Total average system supply currents must be less than 30A. Low power, reliable, and efficient network operation is obtained with intelligent sensor nodes that include sensor signal processing, control, and a wireless network interface. Distributed network sensor devices must continuously monitor multiple sensor systems, process sensor signals, and adapt to changing environments and user requirements, while completing decisions on measured signals.
Figure 2. WINS nodes (shown as disks)
For the particular applications of military security, the WINS sensor systems must operate at low power, sampling at low frequency and with environmental background limited sensitivity. The micro power interface circuits must sample at dc or low frequency where 1/f noise in these CMOS interfaces is large. The micropower signal processing system must be implemented at low power and with limited word length. In particular, WINS applications are generally tolerant to latency. The WINS node event recognition may be delayed by 10 “ 100 msec, or longer.
4. WINS MICRO SENSORS
Source signals (seismic, infrared, acoustic and others) all decay in amplitude rapidly with radial distance from the source. To maximize detection range, sensor sensitivity must be optimized. In addition, due to the fundamental limits of background noise, a maximum detection range exists for any sensor. Thus, it is critical to obtain the greatest sensitivity and to develop compact sensors that may be widely distributed. Clearly, microelectromechanical systems (MEMS) technology provides an ideal path for implementation of these highly distributed systems. The sensor-substrate Sensorstrate is then a platform for support of interface, signal processing, and communication circuits. Examples of WINS Micro Seismometer and infrared detector devices are shown in Figure 3. The detector shown is the thermal detector. It just captures the harmonic signals produced by the foot-steps of the stranger entering the border. These signals are then converted into their PSD values and are then compared with the reference values set by the user.
Figure 3. Thermal Infrared Detector
5. ROUTING BETWEEN NODES
The sensed signals are then routed to the major node. This routing is done based on the shortest distance. That is the distance between the nodes is not considered, but the traffic between the nodes is considered. This has been depicted in the figure 4. In the figure, the distances between the nodes and the traffic between the nodes has been clearly shown. For example, if we want to route the signal from the node 2 to node 4, the shortest distance route will be from node 2 via node 3 to node 4. But the traffic through this path is higher than the path node 2 to node 4. Whereas this path is longer in distance.
Figure 4. Nodal distance and Traffic
6. SHORTEST DISTANCE ALGORITHM
In this process we find mean packet delay, if the capacity and average flow are known. From the mean delays on all the lines, we calculate a flow-weighted average to get mean packet delay for the whole subnet. The weights on the arcs in the figure 5 give capacities in each direction measured in kbps.
Figure 5. Subnet with line capacities Figure 6.s Routing Matrix
In fig 6 the routes and the number of packets/sec sent from source to destination are shown. For example, the E-B traffic gives 2 packets/sec to the EF line and also 2 packets/sec to the FB line. The mean delay in each line is calculated using the formula
Ti =1/(µc-)
Ti = Time delay in sec
C = Capacity of the path in Bps
µ = Mean packet size in bits
= Mean flow in packets/sec.
¬¬
The mean delay time for the entire subnet is derived from weighted sum of all the lines. There are different flows to get new average delay. But we find the path, which has the smallest mean delay-using program. Then we calculate the Waiting factor for each path. The path, which has low waiting factor, is the shortest path. The waiting factor is calculated using
W = i /
i = Mean packet flow in path
= Mean packet flow in subnet
The tabular column listed below gives waiting factor for each path.
Figure 5. WINS Comparator response
7. WINS DIGITAL SIGNAL PROCESSING
If a stranger enters the border, his foot-steps will generate harmonic signals. It can be detected as a characteristic feature in a signal power spectrum. Thus, a spectrum analyzer must be implemented in the WINS digital signal processing system. The spectrum analyzer resolves the WINS input data into a low-resolution power spectrum. Power spectral density (PSD) in each frequency bins is computed with adjustable band location and width. Bandwidth and position for each power spectrum bin is matched to the specific detection problem. The WINS spectrum analyzer must operate at W power level. So the complete WINS system, containing controller and wireless network interface components, achieves low power operation by maintaining only the micropower components in continuous operation. The WINS spectrum analyzer system, shown in Figure 7, contains a set of parallel filters.
Figure 7. WINS micropower spectrum analyzer architecture.
8. PSD COMPARISION
Each filter is assigned a coefficient set for PSD computation. Finally, PSD values are compared with background reference values In the event that the measured PSD spectrum values exceed that of the background reference values, the operation of a microcontroller is triggered. Thus, only if an event appears, the micro controller operates. Buffered data is stored during continuous computation of the PSD spectrum. If an event is detected, the input data time series, including that acquired prior to the event, are available to the micro controller. The micro controller sends a HIGH signal, if the difference is high. It sends a LOW signal, if the difference is low. For a reference value of 25db, the comparison of the DFT signals is shown in the figure 8.
Figure 8. Comparator plot
9. WINS MICROPOWER EMBEDDED RADIO
WINS systems present novel requirements for low cost, low power, short range, and low bit rate RF communication. Simulation and experimental verification in the field indicate that the embedded radio network must include spread spectrum signaling, channel coding, and time division multiple access (TDMA) network protocols. The operating bands for the embedded radio are most conveniently the unlicensed bands at 902-928 MHz and near 2.4 GHz. These bands provide a compromise between the power cost associated with high frequency operation and the penalty in antenna gain reduction with decreasing frequency for compact antennas. The prototype, operational, WINS networks are implemented with a self-assembling, multihop TDMA network protocol.
The WINS embedded radio development is directed to CMOS circuit technology to permit low cost fabrication along with the additional WINS components. In addition, WINS embedded radio design must address the peak current limitation of typical battery sources, of 1mA. It is critical, therefore, to develop the methods for design of micropower CMOS active elements. For LC oscillator phase noise power, S, at frequency offset of away from the carrier at frequency with an input noise power, Snoise and LC tank quality factor, Q, phase noise power is:
Now, phase noise power, Snoise, at the transistor input, is dominated by 1/f noise. Input referred thermal noise, in addition, increases with decreasing drain current and power dissipation due to the resulting decrease in transistor transconductance. The tunability of micropower CMOS systems has been tested by implementation of several VCO systems to be discussed below. The embedded radio system requires narrow band operation and must exploit high Q value components.
10. CONCLUSION
A series of interface, signal processing, and communication systems have been implemented in micropower CMOS circuits. A micropower spectrum analyzer has been developed to enable low power operation of the entire WINS system. Thus WINS require a Microwatt of power. But it is very cheaper when compared to other security systems such as RADAR under use. It is even used for short distance communication less than 1 Km. It produces a less amount of delay. Hence it is reasonably faster. On a global scale, WINS will permit monitoring of land, water, and air resources for environmental monitoring. On a national scale, transportation systems, and borders will be monitored for efficiency, safety, and security.
Reply
swathid90
Active In SP
**

Posts: 1
Joined: May 2010
#4
06-05-2010, 09:30 PM

plz provide me with some more matter regarding border security using wins and is this technology is in use currently??
Reply
munnu
Active In SP
**

Posts: 1
Joined: May 2010
#5
18-05-2010, 01:33 PM

plz send me the complete report
Reply
seminar presentation
Active In SP
**

Posts: 582
Joined: Apr 2010
#6
18-05-2010, 02:23 PM

any registered user can download the report from attachment topicideashow-to-border-security-using-wireless-integrated-network-sensors-wins
Use Search at http://topicideas.net/search.php wisely To Get Information About Project Topic and Seminar ideas with report/source code along pdf and ppt presenaion
Reply
tagore.chandan
Active In SP
**

Posts: 1
Joined: Dec 2010
#7
30-12-2010, 06:32 PM

Can u please help me by sending complete details of each module....like circuit diagrams and experimental data so on....im interested in doing this project and implimentation for my final year b.tech...thanx in advance....

tagore.chandan@ gmail.com

Reply
seminar surveyer
Active In SP
**

Posts: 3,541
Joined: Sep 2010
#8
31-12-2010, 10:49 AM

go through the following thread please..

topicideashow-to-border-security-using-wireless-integrated-network-sensors
Reply
kiran788
Active In SP
**

Posts: 2
Joined: Jan 2011
#9
02-01-2011, 09:41 PM

please send the information and ppt regarding this.
Reply
seminar surveyer
Active In SP
**

Posts: 3,541
Joined: Sep 2010
#10
03-01-2011, 09:39 AM

please visit the previous page for ppt and reports on this topic.
Reply
sushma reddy
Active In SP
**

Posts: 1
Joined: Feb 2011
#11
09-02-2011, 12:51 PM

Thanks 4 ur reportSmileplz send ppt and complete report on border security using wireless integrated network sensors..........
thanks 4 ur report. .pls send d ppt nd complete details on border security using wireless integrated network sensors(WINS)..
pls send d ppt tday. .
Reply
seminar class
Active In SP
**

Posts: 5,361
Joined: Feb 2011
#12
01-03-2011, 02:52 PM

presented by:
M. Sai Anil Kumar
B. V. Vinod K Reddy


.pptx   Wins.pptx (Size: 521.65 KB / Downloads: 116)
Border Security Using W.I.N.S
Introduction:

 Wireless Integrated Network Sensors (WINS) has
a. Sensing
b. Signal Processing
c. Decision Capability
d. Wireless Networking Capability
W.I.N.S. Architecture
Wireless Networks

 Supported by Complex Protocols.
 Long Range
 Bit Rate of 100 kbps
W.I.N.S. Network
 Support Number of Sensors.
 Short Range
 Bit Rate less than 1 kbps
Node Architecture
 Node Architecture must enable
 Continuous Sensing
 Event Detection
 Event Identification
 At Low Cost
W.I.N.S. Micro Sensors
 Source Signals decay in Amplitude.
 Maximize Range à Optimized Sensitivity
 Critical to Develop Sensors.
 M.E.M.S. Technology is Ideal.
 Sensor Substrate is useful in processing and communication.
Routing Between Nodes:
 Routing is based on Shortest distance.
 Traffic between nodes is considered.
D.S.P. In W.I.N.S.
 Spectrum Analyzer is used.
 It resolves input as Low Resolution Power Spectrum.
P.S.D. Comparison:
 P.S.D. values are compared with reference values.
 If Event occurs, levels changes and Micro Controller Triggers.
Reply
seminar class
Active In SP
**

Posts: 5,361
Joined: Feb 2011
#13
24-03-2011, 11:24 AM

Presented By:
POOJA.V.VERNEKAR


.docx   seminar.docx (Size: 170.32 KB / Downloads: 73)
ABSTRACT
Wireless Integrated Network Sensors (WINS) now provide a new monitoring and control capability for monitoring the borders of the country. Using this concept we can easily identify a stranger or some terrorists entering the border. The border area is divided into number of nodes. Each node is in contact with each other and with the main node. The noise produced by the foot-steps of the stranger is collected using the sensor. This sensed signal is then converted into power spectral density and the compared with reference value of our convenience. Accordingly the compared value is processed using a microprocessor, which sends appropriate signals to the main node. Thus the stranger is identified at the main node. A series of interface, signal processing, and communication systems have been implemented in micro power CMOS circuits. A micro power spectrum analyzer has been developed to enable low power operation of the entire WINS system.
Thus WINS require a Microwatt of power. But it is very cheaper when compared to other security systems such as RADAR under use. It is even used for short distance communication less than 1 Km. It produces a less amount of delay. Hence it is reasonably faster. On a global scale, WINS will permit monitoring of land, water, and air resources for environmental monitoring. On a national scale, transportation systems, and borders will be monitored for efficiency, safety, and security.
BORDER SECURITY USING
WIRELESS INTEGRATED NETWORK SENSORS (WINS)
1. INTRODUCTION

Wireless Integrated Network Sensors (WINS) combine sensing, signal processing, decision capability, and wireless networking capability in a compact, low power system. Compact geometry and low cost allows WINS to be embedded and distributed at a small fraction of the cost of conventional wireline sensor and actuator systems. On a local, wide-area scale, battlefield situational awareness will provide personnel health monitoring and enhance security and efficiency. Also, on a metropolitan scale, new traffic, security, emergency, and disaster recovery services will be enabled by WINS. On a local, enterprise scale, WINS will create a manufacturing information service for cost and quality control. The opportunities for WINS depend on the development of scalable, low cost, sensor network architecture. This requires that sensor information be conveyed to the user at low bit rate with low power transceivers. Continuous sensor signal processing must be provided to enable constant monitoring of events in an environment. Distributed signal processing and decision making enable events to be identified at the remote sensor. Thus, information in the form of decisions is conveyed in short message packets. Future applications of distributed embedded processors and sensors will require massive numbers of devices. In this paper we have concentrated in the most important application, Border Security.
2. WINS SYSTEM ARCHITECTURE
Conventional wireless networks are supported by complex protocols that are developed for voice and data transmission for handhelds and mobile terminals. These networks are also developed to support communication over long range (up to 1km or more) with link bit rate over 100kbps. In contrast to conventional wireless networks, the WINS network must support large numbers of sensors in a local area with short range and low average bit rate communication (less than 1kbps). The network design must consider the requirement to service dense sensor distributions with an emphasis on recovering environment information. Multihop communication yields large power and scalability advantages for WINS networks. Multihop communication, therefore, provides an immediate advance in capability for the WINS narrow Bandwidth devices. However, WINS Multihop Communication networks permit large power reduction and the implementation of dense node distribution. The multihop communication has been shown in the figure 2. The figure 1 represents the general structure of the wireless integrated network sensors (WINS) arrangement.
3. WINS NODE ARCHITECTURE
The WINS node architecture (Figure 1) is developed to enable continuous sensing, event detection, and event identification at low power. Since the event detection process must occur continuously, the sensor, data converter, data buffer, and spectrum analyzer must all operate at micro power levels. In the event that an event is detected, the spectrum analyzer output may trigger the microcontroller. The microcontroller may then issue commands for additional signal processing operations for identification of the event signal. Protocols for node operation then determine whether a remote user or neighboring WINS node should be alerted. The WINS node then supplies an attribute of the identified event, for example, the address of the event in an event look-up-table stored in all network nodes. Total average system supply currents must be less than 30A. Low power, reliable, and efficient network operation is obtained with intelligent sensor nodes that include sensor signal processing, control, and a wireless network interface. Distributed network sensor devices must continuously monitor multiple sensor systems, process sensor signals, and adapt to changing environments and user requirements, while completing decisions on measured signals.
For the particular applications of military security, the WINS sensor systems must operate at low power, sampling at low frequency and with environmental background limited sensitivity. The micro power interface circuits must sample at dc or low frequency where “1/f” noise in these CMOS interfaces is large. The micropower signal processing system must be implemented at low power and with limited word length.The WINS node event recognition may be delayed by 10 – 100 msec, or longer.
4. ROUTING BETWEEN NODES
The sensed signals are then routed to the major node. This routing is done based on the shortest distance. That is the distance between the nodes is not considered, but the traffic between the nodes is considered.
5. WINS DIGITAL SIGNAL PROCESSING
If a stranger enters the border, his foot-steps will generate harmonic signals. It can be detected as a characteristic feature in a signal power spectrum. Thus, a spectrum analyzer must be implemented in the WINS digital signal processing system. The spectrum analyzer resolves the WINS input data into a low-resolution power spectrum. Power spectral density (PSD) in each frequency “bins” is computed with adjustable band location and width. Bandwidth and position for each power spectrum bin is matched to the specific detection problem. The WINS spectrum analyzer must operate at W power level. So the complete WINS system, containing controller and wireless network interface components, achieves low power operation by maintaining only the micropower components in continuous operation. The WINS spectrum analyzer system, shown in Figure 7, contains a set of parallel filters.
6. PSD COMPARISION
Each filter is assigned a coefficient set for PSD computation. Finally, PSD values are compared with background reference values In the event that the measured PSD spectrum values exceed that of the background reference values, the operation of a microcontroller is triggered. Thus, only if an event appears, the micro controller operates. Buffered data is stored during continuous computation of the PSD spectrum.
CONCLUSION
A series of interface, signal processing, and communication systems have been implemented in micropower CMOS circuits. A micropower spectrum analyzer has been developed to enable low power operation of the entire WINS system. Thus WINS require a Microwatt of power. But it is very cheaper when compared to other security systems such as RADAR under use. It is even used for short distance communication less than 1 Km. It produces a less amount of delay. Hence it is reasonably faster. On a global scale, WINS will permit monitoring of land, water, and air resources for environmental monitoring. On a national scale, transportation systems, and borders will be monitored for efficiency, safety, and security.
Reply
soujanya.k2
Active In SP
**

Posts: 2
Joined: Mar 2011
#14
25-03-2011, 02:52 PM

can u send me the pdf formate of boarder security of wireless integrated network sensor(wins)
Reply
soujanya.k2
Active In SP
**

Posts: 2
Joined: Mar 2011
#15
25-03-2011, 03:06 PM

i want pdf of BORDER SECURITY USING WIRELESS INTEGRATED NETWORK SENSORS (WINS
)by tommorrow plz send it to my mail by tommorrow morning
Reply

Important Note..!

If you are not satisfied with above reply ,..Please

ASK HERE

So that we will collect data for you and will made reply to the request....OR try below "QUICK REPLY" box to add a reply to this page

Quick Reply
Message
Type your reply to this message here.


Image Verification
Please enter the text contained within the image into the text box below it. This process is used to prevent automated spam bots.
Image Verification
(case insensitive)

Possibly Related Threads...
Thread Author Replies Views Last Post
  WIRELESS MIROSERWER seminar ideas 2 690 09-04-2016, 12:35 PM
Last Post: mkaasees
  integrated starter generator jaseelati 0 212 25-02-2015, 01:38 PM
Last Post: jaseelati
  wireless electricity transmission ppt jaseelati 0 337 09-02-2015, 02:38 PM
Last Post: jaseelati
  gps based border alert system for fishermen jaseelati 0 284 31-01-2015, 03:19 PM
Last Post: jaseelati
  global wireless e-voting ppt jaseelati 0 334 23-01-2015, 04:19 PM
Last Post: jaseelati
  elastic optical network wiki jaseelati 0 283 22-01-2015, 02:07 PM
Last Post: jaseelati
  ppt on trends in wireless computing jaseelati 0 277 21-01-2015, 03:23 PM
Last Post: jaseelati
  network intrusion detection system project report doc jaseelati 0 383 13-01-2015, 01:15 PM
Last Post: jaseelati
  wireless power theft monitoring system and indication at local substations. jaseelati 0 363 10-01-2015, 03:42 PM
Last Post: jaseelati
  intelligent wireless video camera wikipedia jaseelati 0 416 07-01-2015, 04:48 PM
Last Post: jaseelati