Driving Optical Network Evolution
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Computer Science Clay
Active In SP
**

Posts: 712
Joined: Jan 2009
#1
01-03-2009, 02:17 PM


Wideband Sigma Delta PLL Modulator

The proliferation of wireless products over past few years has been rapidly increasing. New wireless standards such as GPRS and HSCSD have brought new challenges to wireless transceiver design. One pivotal component of transceiver is frequency synthesizer.

Two major requirements in mobile applications are efficient utilization of frequency spectrum by narrowing the channel spacing and fast switching for high data rates. This can be achieved by using fractional- N PLL architecture. They are capable of synthesizing frequencies at channel spacings less than reference frequency. This will increase the reference frequency and also reduces the PLL's lock time.

Fractional N PLL has the disadvantage that it generates high tones at multiple of channel spacing. Using digital sigma delta modulation techniques. we can randomize the frequency division ratio so that quantization noise of the divider can be transferred to high frequencies thereby eliminatory the spurs.

Conventional PLL

The advantages of this conventional PLL modulator is that they offer small frequency resolution, wider tuning bandwidth and fast switching speed. But they have insufficient bandwidth for current wireless standards such as GSM. so that they cannot be used as a closed loop modulator for digital enhanced codeless (DECT) standard. they efficiently filter out quantization noise and reference feed through for sufficiently small loop bandwidth.

Wide Band PLL

For wider loop band width applications bandwidth is increased. but this will results in residual spurs to occur. this due to the fact that the requirement of the quantization noise to be uniformly distributed is violated. since we are using techniques for frequency synthesis the I/P to the modulator is dc I/P which will results in producing tones even when higher order modulators are used. with single bit O/P level of quantization noise is less but with multi bit O/P s quantization noise increases.

So the range of stability of modulator is reduced which will results in reduction of tuning range. More over the hardware complexity of the modulator is higher than Mash modulator. In this feed back feed forward modulator the loop band width was limited to nearly three orders of magnitudes less than the reference frequency. So if it is to be used as a closed loop modulator power dissipation will increase.

So in order to widen the loop band width the close-in-phase noise must be kept within tolerable levels and also the rise of the quantization noise must be limited to meet high frequency offset phase noise requirements. At low frequencies or dc the modulator transfer function has a zero which will results in addition of phase noise. For that the zero is moved away from dc to a frequency equal to some multiple of fractional division ratio. This will introduce a notch at that frequency which will reduce the total quantization noise. Now the quantization noise of modified modulator is 1.7 times and 4.25 times smaller than Mash modulator.

At higher frequencies quantization noise cause distortion in the response. This is because the step size of multi bit modulator is same as single bit modulator. So more phase distortion will be occurring in multi bit PLLs. To reduce quantization noise at high frequencies the step size is reduced by producing functional division ratios. This is achieved by using a phase selection divider instead of control logic in conventional modulator. This divider will produce phase shifts of VCO signal and changes the division ratio by selecting different phases from the VCO. This type of divider will produce quarter division ratios.
Use Search at http://topicideas.net/search.php wisely To Get Information About Project Topic and Seminar ideas with report/source code along pdf and ppt presenaion
Reply

Important Note..!

If you are not satisfied with above reply ,..Please

ASK HERE

So that we will collect data for you and will made reply to the request....OR try below "QUICK REPLY" box to add a reply to this page

Quick Reply
Message
Type your reply to this message here.


Image Verification
Please enter the text contained within the image into the text box below it. This process is used to prevent automated spam bots.
Image Verification
(case insensitive)

Possibly Related Threads...
Thread Author Replies Views Last Post
  elastic optical network wiki jaseelati 0 262 22-01-2015, 02:07 PM
Last Post: jaseelati
  network intrusion detection system project report doc jaseelati 0 366 13-01-2015, 01:15 PM
Last Post: jaseelati
  optical technology in current measurement jaseelati 0 306 10-01-2015, 01:19 PM
Last Post: jaseelati
  network intrusion detection system project report jaseelati 0 245 23-12-2014, 03:08 PM
Last Post: jaseelati
  the client/server network strategy can handle very large networks efficiently. jaseelati 0 266 11-12-2014, 02:17 PM
Last Post: jaseelati
  WIRELESS INTEGRATED NETWORK SENSORS ppt study tips 0 479 27-08-2013, 03:06 PM
Last Post: study tips
  Robot Assisted Emergency Search and Rescue System With a Wireless Sensor Network pdf study tips 0 618 23-08-2013, 03:22 PM
Last Post: study tips
  Acousto-Ultrasonic Optical Fiber Sensors PPT study tips 0 373 30-07-2013, 03:16 PM
Last Post: study tips
  Report on Optical Fibers study tips 0 306 13-07-2013, 12:05 PM
Last Post: study tips
  GSM NETWORK & ARCHITECTURE ppt study tips 0 499 09-07-2013, 02:51 PM
Last Post: study tips