Dual-tone Multi-Frequency (DTMF) signaling
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
project report tiger
Active In SP
**

Posts: 1,062
Joined: Feb 2010
#1
01-03-2010, 07:24 PM



.doc   SYNOPSIS.doc (Size: 52 KB / Downloads: 119)

SYNOPSIS
Dual-tone Multi-Frequency (DTMF) signaling is the basis for voice communications control and is widely used worldwide in modern telephony to dial numbers and configure switchboards. It is also used in systems such as in voice mail, electronic mail and telephone banking.
The detector part of early DTMF systems consisted of analog implemented bandpass filter banks, which were tuned to the eight standard frequencies. As analog lines as well as many other analog systems were converted to digital, researchers became interested in digital DTMF detectors. Digital implementation has many advantages over analog implementation such as accuracy, stability, re-programmability, and chip count; that is, instead of using several analog chips for detecting multi-channel DTMF tones, only a digital signal processor (DSP) chip is used for all channels.
The DTMF coding is based on two tones used to generate a digit. Two of eight tones can be combined so as to generate sixteen different DTMF digits. The DTMF decoding is based on the discrete Fourier transform (DFT). Using this algorithm, 12 DTMF receiver can be implemented on 4 X 3 frequency Goertzel algorithm function blocks. Then, the output of Goertzel algorithm can be decoded into a digit.
The present project and implimentation performs twist computations only when the signal has become stable, thus achieving more accuracy and reliability. The DTMF detector receives a set of digital samples of a received signal and calculates energy values for each of the set of different uncorrelated frequencies.
A DTMF signal consists of two superimposed sinusoidal waveforms whose frequencies are chosen from a set of seven standardized frequencies. The frequencies are so chosen to prevent any harmonics being incorrectly detected as a valid signal. The frequency pairs chosen are as shown below.

Figure 1
For example, by pressing the 1 button on the touch-tone telephone key pad , a signal consisting of a 697 Hz sinusoid and a 1209 Hz sinusoid is generated. A DTMF detector attempts to detect these frequencies in the presence of noise, and determines which button is pressed. This detection is done using the Goertzel Algorithm. The difficulty of DTMF tone detection is due to the standards which must be satisfied when these signals are detected.

Here we use a standard telephone instrument; the line-in of this instrument is tapped and given to the interface circuit which acts as an interface between telephone line and DSK6416 kit.
Here DSK6416 kit is used as a decoder which decodes the DTMF signal and displays the value of the corresponding key pressed on the LED.
Reply
seminar flower
Super Moderator
******

Posts: 10,120
Joined: Apr 2012
#2
21-06-2012, 05:53 PM

Dual Tone Multi Frequency


.ppt   Dual Tone Multi Frequency.ppt (Size: 263 KB / Downloads: 37)
DTMF

Method to instruct the telephone switching system of number to be dialed
To issue commands to switching system or related telephony systems
Numbers and commands issued from a keypad
Used mostly in interactive response systems

Transmission using RTP

Payload format designated as “telephone-event”
Media type is “audio/telephone-event”
Carried as part of audio stream
Considered a very highly compressed audio codec

Security

Telephone event payload highly compressed
Very high sensitivity to even small changes in bit values
Secure Real Time Protocol must be implemented

Conclusion

DTMF maps keypad characters to a combination of predefined frequencies
Transported as an RTP payload and decoded using Goertzel algorithm
KPML enables transport of mid-call key press information
A SIP-centric model that makes use of DRegex.


Reply

Important Note..!

If you are not satisfied with above reply ,..Please

ASK HERE

So that we will collect data for you and will made reply to the request....OR try below "QUICK REPLY" box to add a reply to this page

Quick Reply
Message
Type your reply to this message here.


Image Verification
Please enter the text contained within the image into the text box below it. This process is used to prevent automated spam bots.
Image Verification
(case insensitive)

Possibly Related Threads...
Thread Author Replies Views Last Post
  MULTI-LEVEL INVERTER CAPABLE OF POWER FACTOR CONTROL WITH DC LINK SWITCHES PPT study tips 2 606 06-09-2016, 10:04 AM
Last Post: Dhanabhagya
  Analog Circuit Design with Multi-Gate and Tunneling FETs seminar poster 0 357 29-10-2013, 03:20 PM
Last Post: seminar poster
  PNEUMATIC MULTI-PURPOSE MACHINE smart paper boy 1 2,220 08-10-2013, 09:45 PM
Last Post: Guest
  A Project report On DTMF VOTING MACHINE seminar projects maker 0 673 26-09-2013, 02:25 PM
Last Post: seminar projects maker
  DTMF BASED MOBILE CONTROLLED CAR WITH AUTOMATIC CONTROLLED HEAD LIGHT pdf seminar projects maker 0 471 13-09-2013, 11:32 AM
Last Post: seminar projects maker
  Report on Zig-bee based multi nodal fault monitoring system study tips 0 348 07-09-2013, 02:12 PM
Last Post: study tips
  Report on Zig-bee based multi nodal fault monitoring system study tips 0 277 07-09-2013, 02:12 PM
Last Post: study tips
  Mobile Controlled ROBOT Using DTMF Technology seminar class 13 21,664 22-07-2013, 10:20 AM
Last Post: study tips
  SOLAR BASED MULTI-BATTERY CHARGER ppt study tips 0 600 20-07-2013, 04:57 PM
Last Post: study tips
  CELL PHONE BASED DTMF CONTROLLED DOOR OPENING SYSTEM ABSTRACT study tips 0 536 03-07-2013, 03:50 PM
Last Post: study tips