Hydrodrive seminar or presentation report
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
mechanical engineering
Active In SP
**

Posts: 13
Joined: Dec 2009
#1
31-12-2009, 08:06 PM



.doc   Hydrodrive seminar report.doc (Size: 237.5 KB / Downloads: 428)
ABSTRACT
Hydro forming is the process by which water pressure is used to form complex shapes from sheet or tube material.
Applications of hydro forming in automotive industry are gaining globally in popularity. The trend in auto manufacturing of making parts lighter and more complicated with necessary strength reinforcement only where required is on the rise. The capability of hydro forming is more fully used to produce such complicated parts.

Chapter “I
INTRODUCTION
Hydro Forming uses water pressure to form complex shapes from sheet or tube material. The pressure may go up about 60,000 psi depending on the component.
As the automobile industry strives to make car lighter, stronger and more fuel efficient, it will continue to drive hydro forming applications. Some automobile parts such as structural chassis, instrument panel beam, engine cradles and radiator closures are becoming standard hydro formed parts.
The capability of hydro forming can be more fully used to create complicated parts. Using a single hydro formed item to replace several individual parts eliminate welding or hole punching, simplifies assembly and reduce inventory.

Chapter -II
TAKING ADVANTAGE OF HYDRO FORMING
When considering hydro forming, companies need to ask whether this technology will make a part cheaper to produce. The real question is whether you can refine the entire manufacturing process to take advantage of hydroforming that is when it really makes.
Instead of looking at a single competent to determine whether it can be hydro formed , companied need to look at a product through whole process, from material to assembly , to determine what savings can be achieved . For e.g. Hydro forming often reduces number of pieces or the amount of floor space used or eliminates the need for welding stations.

Chapter -III
METHODS OF HYDRO FORMING
Tube Hydro forming

Straight, pre bent and or performed tubes are formed by internal water pressure with additional application of compressive mechanical forces. In this method the tube in placed in die and as press clamps the die valves, low pressure fluid in introduced into tube to pre form it.
One the maximum clamping pressure in achieved, the fluid pressure inside the tube in increased so that tube bulges to take internal shape of the die. Simultaneously additional cylinders axially compress the tube to prevent thinning and brushing swing expansion.



Chapter “IV
HOW CAN TUBE HYDRO FORMING BENEFIT
THE AUTO MANUFACTURER
¢ Increased strength to weight ratios
¢ Multiple cross “ section reshaping or section modules increase
¢ Improved stiffness torsion and bending rigidly
¢ Improvement in NHV Factor
¢ Incorporation of hole punching, slot making, embosses swing hydro forming process.
¢ Reduction in number of manufacturing stages, hence tooling.
¢ Reduction in welding, hence distortion and subsequent heat treatment.

Chapter “V
SHEET HYDRO FORMING
Sheet hydro forming involves forming of sheet with application of fluid pressure. A sheet metal blank informed by hydraulic counter pressure generated by punch drawing sheet into pressurized water chambers. The water pressure effectively punches the sheet firmly against punch to form required shape.
The major advantage of fluid forming is increased drawing ratio. The process tale place in two stages performed during one press stroke. The sheet in performed by applying low fluid pressure while it is in clamped firmly by a blank holder pressure. Performing achieves on evenly distributed strengthening in the component center. In next step fluid pressure in gradually increased and blank holder pressure in controlled relative to sheet reformation.



Chapter -VI
THE APPLICATION SPECTRUM
There are numerous automotive components well suited to hydro forming of sheets. This is especially true in area of outer skin with its extreme demand of surface quality and dimensional accuracy. Longer outer skin parts for passenger cars, utility vehicles and truck such as goods, doors and tender as well as complex structural components can be formed

Chapter -VII
HYDRO FORMING PROCESS CONTROL
A typical hydro forming system would include a press capable of developing necessary forces to clamp the die valves together when internal pressure acts on fluid; a high pressure water system to intensify water pressure for forming component, looking including aerial cylinder and punches, depending on component and a control system for process monitoring.
Since the entire process of operation takes place inside a closed die, one cannot see what actually happens during forming. Therefore the controller plays a vital role in displaying, monitoring and controlling the different parameters of forming in real time.



Chapter - VIII
NEW CONCEPT IN SHEET HYDRO FORMING
DOUBLE SHEET HYDRO FORMING
Structural component with closed components are formed by this process. Some advantages of this process are:-
1. Integration of more parts, further reduction of components & thus steps.
2. Stiffness increase and reduction in overall spring back due to closed box section & continuous weld section.
3. A complete component is made in one single hydroforming step, with only top and bottom die .

Chapter -IX
HYDRO PATH WORK OR HYDRO FORMED
TAILORED BLANK
By this method, the need for additional forming / joining operation in unnecessary. It is used in areas where sound insulation and vibration damping is required & where high degree of energy absorption during crash in needed. The additional or path sheet could be of same or different material or different thickness from parent material.

Chapter -X
HYDRO JOINING
Usually after hydro forming, additional joining operations are required to form assemblies. To reduce manufacturing time and number of process steps, joining operation are being integrated into hydro forming process. This also reduces tool cost. Two approaches to hydro joining are punch riveting hydro clinching.
In punch riveting, pressurized fluid acts on one sheet while a moving punch acts on other sheets from opposite sheet . Punch is moved against rivet and under the fluid counter pressure it spreads to form a solid , visually attractive joint .
In hydro clinching, high pressure fluid action the punch. The prescribed fluid presses the material to be hydro formed part through a note in sheet to be joined .

CONCLUSION
During the last 12 years, general awareness of hydro forming has grown steadily . Although interest in hydroforming is wide ranging , the vast majority of application are in automobile industry .
Hydro Forming is not panacea for manufacturing all automotive parts. The benefits of automotive light weight resin and weight reduction achieved by hydroforming can be measured in kilogram. It cannot be applied to every components, one has to study inability of hydro forming the part and the economic and technical payback.
Just like transistor revolutionized the electronic industry, hydro forming has taken the vehicle manufacturing industry a step up to evolutionary ladder, allowing auto component for vehicle . Although hydroforming has not taken off rapidly as it should have , is only matter on time before this technology is absorbed in the industry .

REFERENCES
1. The Machinist Journal (October Edition)
2. howstuffworks.com


CONTENTS
1. Introduction 1
2. Taking advantage of Hydro forming 2
3. Methods of Hydro forming 3
4. Tube Hydro forming 3
5. How can Tube Manufacturing benefit the auto manufacturers? 5
6. Sheet Hydro Forming 6
7. The Application Spectrum of Sheet Hydro Forming 8
8. Hydro forming process control 9
9. New concept in sheet Hydro forming 11
10. Double sheet hydroforming 11
11. Hydro path work or hydroformed tailored blank 12
12. Hydro joining 13
13. Conclusion 14
14. References 15

ACKNOWLEDGEMENT
First of all I thank the almighty for providing me with the strength and courage to present the seminar and presentation.
I avail this opportunity to express my sincere gratitude towards
Dr. T.N. Sathyanesan, head of mechanical engineering department, for permitting me to conduct the seminar and presentation. I also at the outset thank and express my profound gratitude to my seminar and presentation guide and staff incharge Asst. Prof.
Mrs. Jumailath Beevi. D., for her inspiring assistance, encouragement and useful guidance.
I am also indebted to all the teaching and non- teaching staff of the department of mechanical engineering for their cooperation and suggestions, which is the spirit behind this report. Last but not the least, I wish to express my sincere thanks to all my friends for their goodwill and constructive ideas.

Zumreen Muzamil
Reply
project report helper
Active In SP
**

Posts: 2,270
Joined: Sep 2010
#2
12-10-2010, 12:15 PM


.doc   Hydrodrive seminar report.doc (Size: 231.5 KB / Downloads: 104)

Hydrodrive seminar and presentation report


INTRODUCTION


Hydro Forming uses water pressure to form complex shapes from sheet or tube material. The pressure may go up about 60,000 psi depending on the component.

As the automobile industry strives to make car lighter, stronger and more fuel efficient, it will continue to drive hydro forming applications. Some automobile parts such as structural chassis, instrument panel beam, engine cradles and radiator closures are becoming standard hydro formed parts.

The capability of hydro forming can be more fully used to create complicated parts. Using a single hydro formed item to replace several individual parts eliminate welding or hole punching, simplifies assembly and reduce inventory.
Reply
seminar tips
Super Moderator
******

Posts: 8,857
Joined: Oct 2012
#3
17-12-2012, 12:51 PM

to get information about the topic "Hydro Drive" full report ppt and related topic refer the link bellow

topicideashow-to-hydrodrive-seminar and presentation-report

topicideashow-to-hydro-drive--1984
Reply

Important Note..!

If you are not satisfied with above reply ,..Please

ASK HERE

So that we will collect data for you and will made reply to the request....OR try below "QUICK REPLY" box to add a reply to this page

Quick Reply
Message
Type your reply to this message here.


Image Verification
Please enter the text contained within the image into the text box below it. This process is used to prevent automated spam bots.
Image Verification
(case insensitive)

Possibly Related Threads...
Thread Author Replies Views Last Post
  A SEMINAR REPORT ON MICROMACHINING seminar projects maker 2 975 27-08-2016, 02:48 PM
Last Post: Dhanabhagya
  SEMINAR REPORT ON ELECTRO-HYDRAULIC BRAKE SYSTEM study tips 1 1,191 06-04-2016, 10:28 AM
Last Post: mkaasees
  anti collision device seminar report jaseelati 0 337 18-02-2015, 03:03 PM
Last Post: jaseelati
  air brake system paper presentation ppt jaseelati 0 332 29-01-2015, 03:23 PM
Last Post: jaseelati
  magnetic refrigeration seminar report pdf jaseelati 0 440 24-01-2015, 04:05 PM
Last Post: jaseelati
  magnetic levitation seminar report jaseelati 0 246 23-01-2015, 02:13 PM
Last Post: jaseelati
  femtocell technology seminar report pdf jaseelati 0 287 27-12-2014, 02:56 PM
Last Post: jaseelati
  inter vehicle communication seminar report pdf jaseelati 0 231 27-12-2014, 02:23 PM
Last Post: jaseelati
  eddy current brakes seminar report jaseelati 0 274 18-12-2014, 04:25 PM
Last Post: jaseelati
  seminar report on driverless car jaseelati 0 224 18-12-2014, 03:44 PM
Last Post: jaseelati