Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
project report helper
Active In SP

Posts: 2,270
Joined: Sep 2010
13-10-2010, 01:04 PM

.pdf   CI-01_Aug07.pdf (Size: 103.49 KB / Downloads: 239)



Protect your mobile phone from unauthorized use or theft using this simple circuit. It can generate a loud chirping sound when somebody attempts to take away the mobile handset. The added feature is that the circuit also works as a mobilecapacitor
seminar class
Active In SP

Posts: 5,361
Joined: Feb 2011
26-02-2011, 11:04 AM

.docx   Mobile Shield.docx (Size: 67.32 KB / Downloads: 101)

Protect your mobile phone from unauthorized use or theft using this simple circuit. It can generate a loud chirping sound when somebody attempts to take away the mobile handset. The added feature is that the circuit also works as a mobile charger.
The circuit is powered by a step-down transformer X1 with rectifier
Diodes D1 and D2 and filter capacitor C1. Regulator IC 7812 (IC1) along with noise filter capacitors C2 and C3 provides regulated power supply. The circuit utilizes two NE555 timer ICs: One as a simple astable multivibrator (IC2) and the second as a monostable (IC3).
The astable multivibrator has timing resistors R1 and R2 but no timing capacitor as it works with stray capacitance. Its pins 6 and 2 are directly connected to a protecting shield made up of 10cm×10cm copper-clad board. The inherent stray capacitance of the circuit is sufficient to given an output frequency of about 25 kHz with R1 and R2. This arrangement provides greater sensitivity and enables the circuit with hand capacitance effect. Output pulses from the oscillator are directly given to trigger pin 2 of the monostable.
The monostable uses a low-value capacitor C6, resistors R3 and preset VR1 for timing. The output frequency of the monostable is adjusted using preset VR1 such that it is slightly less than that of the astable. This makes the circuit standby, when there is no hand capacitance present. So in the standby mode, the astable’s output will be low. This makes the trigger input of monostable low and output high.
The warning LED1 and buzzer are connected such that they become active only when the output of the monostable sinks current. In the standby state, the LED1 remains ‘off’ and the buzzer is silent. As somebody tries to take the mobile phone from the protecting shield, his hand comes
Near the shield or makes contact with the shield, which introduces hand capacitance in the circuit.
As a result, the astable’s frequency changes, which makes the trigger pin of the monostable low and its output osciloscillates.
This produces chirping sound from the buzzer and also makes the LED1 blink. The circuit can also be used as a mobile charger. It provides output of 6V at 180 mA through regulator IC 7806 (IC4) and resistor R5 for charging the mobile phone. Diode D3 protects the output from Polarity reversal. The circuit can be wired on a common PCB. Enclose it in a suitable case with provision for charger output leads.
Make the protective shield
Using 10cm×10cm copper-clad board or aluminium sheet. Connect it to the circuit using a 15cm plastic wire. Leads of all capacitors should be short. Adjust VR1 slowly using a plastic screwdriver until the buzzer stops sounding.
Bring the hand close to the shield and adjust VR1 until the buzzer sounds. With trial-and-error procedure, set it for the maximum sensitivity
Such that as soon the hand comes near the shield, the buzzer starts chirpring and the LED blinks. Instead of using the copper cladding for shield, a metallic mobile phone holder can be
Used as the shield.
Active In SP

Posts: 1
Joined: Sep 2011
16-09-2011, 02:04 PM

where i can get pcb layout of mobile shield
seminar addict
Super Moderator

Posts: 6,592
Joined: Jul 2011
17-09-2011, 09:34 AM

To get more information about the topic " MOBILE SHIELD" please refer the link below
seminar tips
Super Moderator

Posts: 8,857
Joined: Oct 2012
10-12-2012, 12:01 PM

to get information about the topic "mobile shield" full report ppt and related topic refer the link bellow



Important Note..!

If you are not satisfied with above reply ,..Please


So that we will collect data for you and will made reply to the request....OR try below "QUICK REPLY" box to add a reply to this page

Quick Reply
Type your reply to this message here.

Image Verification
Please enter the text contained within the image into the text box below it. This process is used to prevent automated spam bots.
Image Verification
(case insensitive)

Possibly Related Threads...
Thread Author Replies Views Last Post
  Bluetooth Enabled Mobile Phone Remote Control for PC PPT seminar flower 2 2,352 05-08-2015, 11:13 PM
Last Post: Guest
  SOLAR BASED MOBILE CHARGER FOR RURAL AREAS PPT seminar flower 2 2,084 07-03-2014, 04:29 PM
Last Post: seminar project topic
  HOME AUTOMATION USING MOBILE COMMUNICATION projectsofme 15 16,382 10-01-2014, 02:20 PM
Last Post: seminar project topic
  MOBILE PHONE TECHNOLOGY seminar girl 2 3,253 10-01-2014, 01:50 PM
Last Post: seminar project topic
  A Self-configurable New Generation Children Tracking System based on Android Mobile project girl 1 1,481 16-10-2013, 03:24 PM
Last Post: Guest
  5G Mobile Technology project uploader 8 6,811 15-10-2013, 07:52 AM
Last Post: Guest
  Mobile Phone Jamming project uploader 23 16,718 03-10-2013, 08:36 AM
Last Post: Guest
  Nericell: rich monitoring of road and traffic conditions using mobile smartphones seminar projects maker 0 444 26-09-2013, 03:58 PM
Last Post: seminar projects maker
  The pothole patrol: using a mobile sensor network for road seminar projects maker 0 526 26-09-2013, 03:56 PM
Last Post: seminar projects maker
  COIN BASED MOBILE CHARGER ABSTRACT seminar projects maker 0 597 25-09-2013, 02:21 PM
Last Post: seminar projects maker