MYOELECTRIC CONTROLLED PROSTHETIC HAND
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
projectsofme
Active In SP
**

Posts: 1,124
Joined: Jun 2010
#1
02-10-2010, 04:48 PM



.doc   MYOELECTRIC CONTROLLED PROSTHETIC HAND.doc (Size: 1.11 MB / Downloads: 112)
This article is presented by:
NARESH . V
BHASKAR. L
MYOELECTRIC CONTROLLED PROSTHETIC HAND


ABSTRACT

Our mini project and implimentation was inductance meter using 89c2051 microcontroller. As an expansion and knowledge improvement we have opted for LCF meter as our final year project and implimentation. Which is not only challenging but also useful device. To be different our choice was LCF meter (inductance , capacitance and frequency meter), instead of LCR meter

INTRODUCTION
Capacitance meter:
Capacitance meter can be very helpful in identifying old components where its mark has been erased or became unreadable. Such instrument can be quite expensive, but fortunately we can build it easily with much lower cost. The capacitance meter described here can measure any capacitor between 1pF and 10uF. Here is the schematic diagram of the circuit:You can just use a connector for the voltmeter, and the circuit becomes a capacitance meter adapter for your general purpose voltmeter. Just plug the input of your voltmeter to this capacitance meter circuit and now your voltmeter becomes capacitance meter.
You can use an analog voltmeter or digital voltmeter. If you use a digital voltmeter, make sure your digital voltmeter is a dual/single slope type reading, since it has an inherent averaging function. If your digital voltmeter is a fast sampling type, then you need to insert a resitor-capacitor filter between this capacitance meter circuit and the voltmeter. A 1k resitor and a 10uF electrolytic capacitor sould be enough for the filter. Analog voltmeter doesn’t need any filter since its mechanical inertia acts like a low-pass filter in nature. More information can be found at
This simple controller based unit was designed to measure and display the values of inductors and capacitors.As a by-product of the technique used.it can also display the frequency of an external 0V/ +5V signal source The ranges are approximately:
Capacitance : 1pF to 6500uF
Inductance : 1uH to 10H
Frequency : 0.05Hz to 5MHz

Inductance meter:
The algorithm works with the device is as follows:
1. After the power, if the buttons SA1, SA2 are pressed, then the indicator will show "L" or "C", thus hinting at what button must be overcome.
2. When squeezed the knob, the instrument calibration mode, as evidenced by the inscription "WAIT", a couple of seconds, alternating on "OK". During this time, the relay, including a reference capacitor in the general contour of the L1 and C1. The microcontroller reads the frequency with condenser and without him, which then e yshem will be used to calculate the exact values of L1 and C1. Measuring terminals at this time disconnected from the circuit and do not affect the measurement.
3. By clicking on the appropriate radio button is selected or the measurement of capacitance or inductance. Accordingly, the indicator displays "L =", or "C =". In the first case, the measured capacitance connected in parallel with C1, the second - as measured inductance connected in series L1. Microcontroller measures the frequency and computes the desired value. The limit of measurement is set automatically, and after the indicated values of the dimension: "pF", "nF", " uH "," mH ".


Frequency counter:
Digital frequency counter is being used for wide range of applications. Digital frequency counter is extensively uses digital circuits and hence fairly good knowledge of digital circuits and of digital integrated circuits is required to understand the operation of the frequency counter. However application of micro controllers have greatly simplified hardware requirement for frequency counter. The following figure shows the conventional frequency counter design.

Reply

Important Note..!

If you are not satisfied with above reply ,..Please

ASK HERE

So that we will collect data for you and will made reply to the request....OR try below "QUICK REPLY" box to add a reply to this page

Quick Reply
Message
Type your reply to this message here.


Image Verification
Please enter the text contained within the image into the text box below it. This process is used to prevent automated spam bots.
Image Verification
(case insensitive)

Possibly Related Threads...
Thread Author Replies Views Last Post
  A VOLTAGE CONTROLLED ADJUSTABLE SPEED PMBLDCM DRIVE USING A SINGLE-STAGE PFC seminar projects maker 0 564 28-09-2013, 02:23 PM
Last Post: seminar projects maker
  DTMF BASED MOBILE CONTROLLED CAR WITH AUTOMATIC CONTROLLED HEAD LIGHT pdf seminar projects maker 0 471 13-09-2013, 11:32 AM
Last Post: seminar projects maker
  A DESIGN OF A PROTOTYPIC HAND –TALK:ASSISTIVE TECHNOLOGY FOR THE DUMB smart paper boy 2 4,491 10-08-2013, 11:15 PM
Last Post: vivekanand.gaikwad30
  Remote Controlled Metal Detecting Robot with Remote Image Transmission seminar class 5 6,634 07-08-2013, 12:32 PM
Last Post: Guest
  REPORT ON GSM CONTROLLED HOME AUTOMATION study tips 0 325 01-08-2013, 01:50 PM
Last Post: study tips
  REPORT ON HAND TALK SYSTEM study tips 0 302 30-07-2013, 04:07 PM
Last Post: study tips
  Mobile Controlled ROBOT Using DTMF Technology seminar class 13 21,664 22-07-2013, 10:20 AM
Last Post: study tips
  VOICE CONTROLLED ROBOT USING BEAGLE BONE REPORT study tips 0 513 17-07-2013, 04:54 PM
Last Post: study tips
  CELL PHONE BASED DTMF CONTROLLED DOOR OPENING SYSTEM ABSTRACT study tips 0 536 03-07-2013, 03:50 PM
Last Post: study tips
  PC CONTROLLED ZIGBEE & GPS NAVIGATED SPY-ROBO FOR ARIEL & TERRESTRIAL PHOTOGRAPHY study tips 0 274 01-07-2013, 02:49 PM
Last Post: study tips