NANOTECHNOLOGY And MECHANICAL ENGINEERING full report
Active In SP
Joined: Mar 2010
09-04-2010, 10:44 PM
nanotechandME.doc (Size: 35 KB / Downloads: 664)
NANOTECHNOLOGY & MECHANICAL ENGINEERING
We live in a world of machines. And the technical foundation for these machines lies in the steam engine developed during the 1780s by James Watt. The concept of deriving useful mechanical work from raw fuel such as wood, coal, oil, and now uranium was revolutionary. Watt also developed the slider-crank mechanism to convert reciprocating motion to rotary motion.
To improve on this first, basic engine, the people who followed Watt created the science of thermodynamics and perfected power transmission through gears, cams, shafts, bearings, and mechanical seals. A new vocabulary involving heat, energy, power, and torque was born with the steam engine.
Nanotechnology in Mechanical Engineering
Just as the steam engine sparked the industrial revolution of the 19th century, nanotechnology will likely ignite a new industrial revolution during the 21st century. Nanotechnology has the potential to impact all industries; the health care and computer industries are already capitalizing on it. New materials are being created that will affect everything from aerospace and energy to recreation and entertainment.
Even more important may be nanoscale machines, devices that function at molecular or even atomic scales. Some pioneers in the field envision the day when nanoscopic robotic submarines will kill off cancers one cell at a time, and foresee nano- scale factories in which tiny arms piece together products molecule by molecule.
And yet, even when discussing such far-out developments, the notion of using an energy source to drive linkages is still a helpful concept in visualizing nanoscale devices. Sure, the sources of energy and the shapes of linkages are still being developed and are open to the designer's imagination. But the design problems associated with nanoscale devices in many instances are little different from those being tackled by engineers working on microelectromechanical systems. In other cases, however, the solutions to problems that arise at the nanoscale have better analogues in biochemistry or physics than in familiar mechanical engineering.
Right now, we need to figure out which is which.
Thanks to physics research conducted with atomic force microscopes and scanning tunneling microscopes, (which image surfaces down to the atomic scale and measure other surface properties such as friction), we know that Newtonian mechanics applies down to the level of just a few atoms. Other forces, such as van der Waals, electrostatic, and capillary, become important at the nanoscale. While these forces are not a factor in the design of MEMS or larger devices, they can be significant forces on nanoscale objects.
For instance, one consideration that makes design at the micro- and nanoscales unique relates to chemical and biological induced loads to machine structures. At present, those kinds of loads are not clearly understood nor are they formulated in a way that lets engineering design predictions be made. This is a major hindrance to the design and commercialization of micro- and nanodevices.
One marketable product that works on that scale which has achieved a level of success is the microcantilever sensor. That platform technology is capable of detecting the presence of certain biological and chemical agents, including explosives, with unprecedented sensitivity. The sensor works by bending when a molecule is adsorbed on one side of the cantilever, and by necessity, the dimensions of these cantilevers are quite small by macro standardsâ€about 200 by 25 micrometers and 1 micrometer thick. This is a different type of beam loading from traditional external forces in macrostructures, and the key to controlling selectivity and sensitivity in design is the fundamental understanding of how biological and chemical agents cause the beams to bend.
In order to design for those types of forces, they first must be formulated in engineering terms or mathematically modeled for computer predictions. The interaction between an adsorbed molecular layer and a silicon surface can be modeled through the use of the Lennard-Jones potential. Total potential energy, including L-J and elastic strain energy in beams, are related to beam curvature. The equilibrium curvature is determined by minimizing total potential energy.
This works for simple situations, but when molecules become longer and more complex, the interactive forces become much more difficult to model. Experiment measurements that can provide the precise relation of potential energies (between specific molecules and surface atoms) to beam curvature are needed. Such data would allow microcantilever sensors to be designed to a given specified level of selectivity, sensitivity, and robustness.
Cantilevers are also being studied for use as microviscometers, which have tremendous applications in fields such as medicine, environmental control, surveillance, automobiles, and petroleum processing. To succeed at this, however, we need an accurate simulation of fluid flow on the surface of vibrating microcantilevers with rectangular cross-sections.
Already, research has shown that the flow around microscale devices is usually laminar and inertial forces are small in comparison with viscous forces. Except for hydrodynamic lubrication, such a situation rarely occurs in macrodevices. These flow characteristics greatly simplify the Navier-Stokes equations. But local and near-surface viscosities may not be the same as bulk viscosity and will probably have to be considered in design.
Designers also must pay attention to friction in nanoscale machines. A recent experiment used corrugated surfaces fabricated on a silicon surface to show that the friction measured by atomic force microscopes is quite sensitive to such factors as peak-to-peak distance. Even relatively smooth surfaces are subject to stick-slip mechanisms at the nanoscale. The magnitude of friction in both cases can be large enough to potentially damage or disable devices. An empirically based model of friction at this scale must be developedâ€and soonâ€in order to predict what level of force various nanodevices can be expected to face.
Beyond modeling, another challenge in designing micro- and nanodevices is the fabrication and testing of prototypes. The performance of macro prototypes normally is measured with proven sensors and instruments, and special diagnostic tools, such as fluorescence microscopy, may be needed to evaluate nanodevice performance. Computer simulation prototyping, based on molecular dynamics, may also be useful here. Either way, engineers must find a way to show that their designs are meeting performance specificationsâ€no mean task when dealing with machines that can be as small as molecules.
Engineers may also have to rethink how they construct complex machines at the nanoscale. At human scales and with MEMS, parts or even whole devices are manufactured by larger ones: A stamping machine turns out metal parts, and computer chips are etched by photolithographic fabricators. It's not clear, however, if this model can be carried to the nanoscale, as the materials and forces involved may well elude top-down control.
Instead, we may find that nanomachines are better assembled from the bottom up. The bottom-up approach offers unlimited possibilities to the design engineer to use the basic building blocks of matter directly.
Eric K. Drexler, one of the founders of nanotechnology as a field of interest, envisioned in the 1980s that it could be possible to assemble certain atoms and molecules, which resemble components commonly used in macro machine design. One could build things from molecule-size bearings, gears, cams, clutches, and so on. This wouldn't be a complete analogue to present-day machine shopsâ€material properties would be softer than in macro materials, for instance, and gear teeth may not satisfy the fundamental gear tooth lawâ€but motion and energy could be transmitted by systems resembling macrodevices. This concept opens up a unique area for machine design at the atomic level.
Use Search at http://topicideas.net/search.php wisely To Get Information About Project Topic and Seminar ideas with report/source code along pdf and ppt presenaion
Active In SP
Joined: Aug 2010
27-08-2010, 11:15 PM
i want do a mechanical project and implimentation in nano technology. can u please give me some ideas or tips about this topic
Joined: Jul 2011
02-02-2012, 10:47 AM
to get information about the topic Mechanical Engineering Project Ideas List full report , refer the link bellow
topicideashow-to-mechanical-engineering-project and implimentation-ideas-list
topicideashow-to-mechanical-engineering-project and implimentation-topics
topicideashow-to-mechanical-engineering-project and implimentation-ideas
topicideashow-to-mechanical-engineering-project and implimentations
topicideashow-to-mechanical-engineering-project and implimentations-for-final-year-students
topicideashow-to-mechanical-engineering-project and implimentation-1-list
topicideashow-to-mechanical-engineering-project and implimentation-ideas?page=2
topicideashow-to-mechanical-engineering-project and implimentation-ideas-list?page=7
Thinking To Register
18-12-2012, 10:56 AM
I am student of B.Tech Mechanical engineering & i want project and implimentation report for final year engineering
subject based on nanotechnology in mechanical engineering .
My email is email@example.com
Joined: Oct 2012
18-12-2012, 11:28 AM
to get information about the topic "nanotechnology" full report ppt and related topic refer the link bellow
topicideashow-to-nanotechnology-download-full-seminar and presentation-report
topicideashow-to-nanotechnology-the-next-science-frontier-seminar and presentation-report
topicideashow-to-seminar and presentation-on-nanotechnology-report
topicideashow-to-nanotechnology-download-full-seminar and presentation-report?page=14