Remote control using VHF modules
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
computer science crazy
Super Moderator
******

Posts: 3,048
Joined: Dec 2008
#1
09-09-2009, 12:31 PM


A few designs for remote control switches, using VG40T and VG40R remote control pair, are shown here.
The miniature transmitter module shown in Fig. 1, which just measures 34 mm x 29 mm x 10 mm, can be used to operate all remote control receiver-cum-switch combinations described in this project and implimentation. A compact 9-volt PP3 battery can be used with the transmitter. It can transmit signals up to 15 metres without any aerial. The operating frequency of the transmitter is 300 MHz. The following circuits, using VG40R remote control receiver module measuring 45 mm x 21 mm x 13 mm, can be used to:

[img]electronic-circuits-diagramsremotecontrolsimages/1.gif[/img]
(a) activate a relay momentarily,
(b) activate a relay for a preset period,
© switch on and switch off a load.
To activate a relay momentarily (see Fig. 2), the switch on the transmitter unit is pressed, and so a positive voltage is obtained at output pin of VG40R module. This voltage is given to bias the relay driver transistor. The relay gets activated by just pressing push-to-on micro switch on the transmitter unit. The relay remains energised as long as the switch remains pressed. When the switch is released, the relay gets deactivated. Any electrical/electronic load can be connected via N/O contacts of the relay.
To activate a relay for a preset period (refer Fig. 3), the switch on the transmitter unit is pressed momentarily. The transistor gets base bias from VG40R module. As a result the transistor conducts and applies a trigger pulse to IC 555, which is wired as a monostable multivibrator. The relay remains activated till the preset time is over. Time delay can be varied from a few seconds to a few minutes by adjusting timing components.
To switch on and switch off a load (refer Fig. 4), a 555 IC and a decade counter 4017 IC are used. Here the 4017 IC is wired as a flip-flop for toggle action. This is achieved by connecting Q2 output to reset terminal while Q1 output is unused. Q0 output is used for energising the relay. The relay is activated and deactivated by pressing the transmitter switch alternately. So, to activate the load, just press the transmitter switch once, momentarily. The relay will remain activated. To switch off the relay, press the transmitter switch again. This process can be repeated. Time delay of monostable multivibrator is set for about one second.
Note: Short length of shielded wire should be used between VG40R receiver module output and the rest of the circuit. The transmitter with 9V battery must be housed inside a nonmetallic (say, plastic) cabinet for maximum range of operation.
Use Search at http://topicideas.net/search.php wisely To Get Information About Project Topic and Seminar ideas with report/source code along pdf and ppt presenaion
Reply

Important Note..!

If you are not satisfied with above reply ,..Please

ASK HERE

So that we will collect data for you and will made reply to the request....OR try below "QUICK REPLY" box to add a reply to this page

Quick Reply
Message
Type your reply to this message here.


Image Verification
Please enter the text contained within the image into the text box below it. This process is used to prevent automated spam bots.
Image Verification
(case insensitive)

Possibly Related Threads...
Thread Author Replies Views Last Post
  MULTI-LEVEL INVERTER CAPABLE OF POWER FACTOR CONTROL WITH DC LINK SWITCHES PPT study tips 2 606 06-09-2016, 10:04 AM
Last Post: Dhanabhagya
  Presentation On Project Automatic Traffic Light Control System ppt study tips 1 740 02-04-2016, 02:28 PM
Last Post: mkaasees
  Bluetooth Enabled Mobile Phone Remote Control for PC PPT seminar flower 2 2,352 05-08-2015, 11:13 PM
Last Post: Guest
  WEATHER MONITORING AND INSTRUMENT CONTROL SYSTEM USING MICROCONTROLLER project report tiger 6 7,070 04-10-2014, 08:55 PM
Last Post: OsKFAHX
  MICROCONTROLLER BASED DAM GATE CONTROL SYSTEM full report seminar class 13 10,280 13-07-2014, 11:33 PM
Last Post: Guest
  Real –Time DC Servo Motor Position Control by PID Controllers Using Labview project girl 3 1,158 20-05-2014, 03:46 PM
Last Post: lucia9901
  REMOTE NOTICE BOARD IMPLEMENTATION USING GSM COMMUNICATION project uploader 2 1,254 09-05-2014, 10:00 AM
Last Post: seminar project topic
  Control of Voltage Source Inverters using PWM/SVPWM for Adjustable Speed Drive project girl 2 1,339 15-03-2014, 03:30 PM
Last Post: seminar project topic
  PLC BASED TRAFFIC CONTROL SYSTEM full report seminar class 5 10,678 10-01-2014, 03:08 PM
Last Post: seminar project topic
  SPEED CONTROL OF DC MOTOR USING PWM TECHNIQUE seminar class 10 24,843 19-10-2013, 07:29 PM
Last Post: Guest