Seasonal Influence on Safety of Substation Grounding
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
computer science crazy
Super Moderator

Posts: 3,048
Joined: Dec 2008
21-09-2008, 10:21 AM


With the development of modern power system to the direction of extra-high voltage, large capacity, far distance transmission and application of advanced technologies the demand on the safety, stability and economic operation of power system became higher. A good grounding system is the fundamental insurance to keep the safe operation of the power system. The good grounding system should ensure the following:

" To provide safety to personnel during normal and fault conditions by limiting step and touch potential.
" To assure correct operation of electrical devices.
" To prevent damage to electrical apparatus.
" To dissipate lightning strokes.
" To stabilize voltage during transient conditions and therefore to minimize the probability of flashover during the transients

As it is stated in the ANSI/IEEE Standard 80-1986 "IEEE Guide for Safety in AC substation grounding," a safe grounding design has two objectives:

" To provide means to carry electric currents into the earth under normal and fault condition without exceeding any operational and equipment limit or adversely affecting continuity of service.
" To assure that a person in the vicinity of grounded facilities is not exposed to the danger of critical electrical shock.

A practical approach to safe grounding considers the interaction of two grounding systems: The intentional ground, consisting of ground electrodes buried at some depth below the earth surface, and the accidental ground, temporarily established by a person exposed to a potential gradient at a grounded facility.

An ideal ground should provide a near zero resistance to remote earth. In practice, the ground potential rise at the facility site increases proportionally to the fault current; the higher the current, the lower the value of total system resistance which must be obtained. For most large substations the ground resistance should be less than 1 Ohm. For smaller distribution substations the usually acceptable range is 1-5 Ohms, depending on the local conditions.
When a grounding system is designed, the fundamental method is to ensure the safety of human beings and power apparatus is to control the step and touch voltages in their respective safe region. step and touch voltage can be defined as follows.

Step Voltage
It is defined as the voltage between the feet of the person standing in near an energized object. It is equal to the difference in voltage given by the voltage distribution curve between two points at different distance from the electrode.

Touch Voltage
It is defined as the voltage between the energized object and the feet of the person in contact with the object. It is equal to the difference in voltage between the object and a point some distance away from it.
In different season, the resistivity of the surface soil layer would be changed. This would affect the safety of grounding systems. The value of step and touch voltage will move towards safe region or to the hazard side is the main concerned question
Use Search at wisely To Get Information About Project Topic and Seminar ideas with report/source code along pdf and ppt presenaion

Important Note..!

If you are not satisfied with above reply ,..Please


So that we will collect data for you and will made reply to the request....OR try below "QUICK REPLY" box to add a reply to this page

Quick Reply
Type your reply to this message here.

Image Verification
Please enter the text contained within the image into the text box below it. This process is used to prevent automated spam bots.
Image Verification
(case insensitive)

Possibly Related Threads...
Thread Author Replies Views Last Post
  gas insulated substation seminar report jaseelati 0 330 18-12-2014, 03:09 PM
Last Post: jaseelati
  Electrical Safety PPT study tips 0 515 13-06-2013, 03:51 PM
Last Post: study tips
  Influence, Power, and Politics PPT study tips 0 307 20-05-2013, 04:44 PM
Last Post: study tips
  SUBSTATION AUTOMATION PPT study tips 0 365 16-05-2013, 04:19 PM
Last Post: study tips
  Electric Substation Monitoring pdf study tips 0 317 08-05-2013, 04:39 PM
Last Post: study tips
  ABCs of multimeter safety seminar tips 0 266 30-11-2012, 06:31 PM
Last Post: seminar tips
  DESIGN CONCEPTS OF 33/11kV NEW SUBSTATION PPT project girl 0 2,156 27-11-2012, 01:03 PM
Last Post: project girl
  Circuit and Safety Analysis System (CSAS), seminar tips 0 329 31-10-2012, 04:26 PM
Last Post: seminar tips
  Artificial Intelligence Substation Control computer science crazy 7 6,925 18-10-2012, 04:16 PM
Last Post: dheerajc46
  Electrical Substation components PPT seminar flower 1 2,185 04-10-2012, 10:54 AM
Last Post: seminar tips