angelo do pietro engine
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
adarshphilip
airman
**

Posts: 1
Joined: Jul 2010
#1
03-07-2010, 09:55 AM


I would like to know more about the air engine developed by angelo di pietro and patented by his company engineair....it is very tough to get the working and structural details and i have gone through most of the sites available during a search. it would be very helpful if anyone have anything more interesting than what is usually seen on such sites.....
Reply
project report helper
Active In SP
**

Posts: 2,270
Joined: Sep 2010
#2
22-09-2010, 11:14 AM

More Info About angelo do pietro engine


Angelo Di Pietro (inventor)
From Wikipedia, the free encyclopedia

Angelo Di Pietro(1950, Avellino, Italy) is an engine designer who developed the Di Pietro Motor air engine. He qualified as Congegniatore Meccanico in Avellino and moved to Stuttgart to work on the Wankel rotary engine at the Mercedes Benz research laboratories 1969 and 1970. In 1971 he migrated to Australia where he established a construction engineering company.


From his early experience with Wankel rotary engines, Angelo became interested in developing a more efficient engine than the traditional reciprocating internal combustion engine, and he has worked on various alternative concepts intermittently over the last 30 years. In 1999 he made a major design breakthrough with a wankel rotary motor which runs on compressed air. Di Pietro claims that his engine is 100% more efficient than competitors' products and that the reduction in friction will allow the engine to turn with a pressure of 1 psi. [1].

Angelo Di Pietros targeted locations in which automotive vehicles are required but cause immense health hazards such as produce markets and warehouse., Angelo Di Pietro was determined to find an alternative that was both environmentally conscious, comparable in desired power, and inexpensive.


Di Pietro Motor

The Di Pietro Motor, developed by the Australian company EngineAir, is a rotary engine powered by compressed air. It is smaller than any internal combustion engine although the size may differ between models.

In difference to other rotary engines, the Di Pietro motor uses a simple cylindrical rotary piston (shaft driver) which rolls, with next to no friction, inside the cylindrical stator. Only 1 psi (≈ 6,8 kPa) of pressure is needed to overcome the friction.[1]

The space between stator and rotor is divided in 6 expansion chambers by pivoting dividers. These dividers follow the motion of the shaft driver as it rolls around the stator wall. The cylindrical shaft driver, forced by the air pressure on its outer wall, moves eccentrically, thereby driving the motor shaft by means of two rolling elements mounted on bearings on the shaft. The rolling motion of the shaft driver inside the stator is cushioned by a thin air film. Timing and duration of the air inlet and exhaust is governed by a slotted timer which is mounted on the output shaft and rotates with the same speed as the motor.

Variation of performance parameters of the motor is achieved by varying the time during which the air is allowed to enter the chamber: A longer air inlet period allows more air to flow into the chamber and therefore results in more torque. A shorter inlet period will limit the air supply and allows the air in the chamber to perform expansion work at a much higher efficiency. In this way compressed air (energy) consumption can be exchanged for higher torque and power output depending on the requirements of the application.

Motor speed and torque are controlled by throttling the amount or pressure of air into the motor. The Di Pietro motor gives instant torque at zero RPM and can be precisely controlled to give soft start and acceleration control.

The Di Pietro Motor can be used in boat, cars, burden carriers and other vehicles.

refered by en.wikipediawiki/Angelo_Di_Pietro_(inventor)
Reply

Important Note..!

If you are not satisfied with above reply ,..Please

ASK HERE

So that we will collect data for you and will made reply to the request....OR try below "QUICK REPLY" box to add a reply to this page

Quick Reply
Message
Type your reply to this message here.


Image Verification
Please enter the text contained within the image into the text box below it. This process is used to prevent automated spam bots.
Image Verification
(case insensitive)

Possibly Related Threads...
Thread Author Replies Views Last Post
  mahindra mhawk scorpio engine timing Guest 1 133 31-10-2016, 03:04 PM
Last Post: jaseela123
Wink disadvantages of nano ic engine Guest 1 92 31-10-2016, 02:57 PM
Last Post: amrutha735
  pdf of mahindra mustang engine Guest 1 62 31-10-2016, 02:48 PM
Last Post: jaseela123
  ppt lean burn technology in si engine Guest 1 83 31-10-2016, 12:17 PM
Last Post: amrutha735
  disadvantages of nano ic engine Guest 1 82 31-10-2016, 11:48 AM
Last Post: jaseela123
  ppt on electromagnetic piston engine Guest 1 47 31-10-2016, 11:22 AM
Last Post: anusree
  animation videos of ball piston engine Guest 1 67 31-10-2016, 11:20 AM
Last Post: jaseela123
  scuderi split cycle engine seminar report Guest 1 90 29-10-2016, 03:53 PM
Last Post: jaseela123
  project report format for fabrication of multi engine compressor Guest 1 60 29-10-2016, 03:39 PM
Last Post: Dhanabhagya
  alcohol sensing alert with engine locking programing Vaibhav1122 1 52 29-10-2016, 12:45 PM
Last Post: jaseela123