programmable Logic Controllers
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Archana Ganesan
Active In SP

Posts: 1
Joined: Dec 2009
07-12-2009, 01:56 PM

I need the seminar and presentation report of "Programmable logic controllers".
Active In SP

Posts: 13
Joined: Jul 2009
07-12-2009, 05:01 PM

Control engineering has evolved over time. In the past humans were the main method for controlling a system. More recently electricity has been used for control and early electrical control was based on relays. These relays allow power to be switched on and off without a mechanical switch. It is common to use relays to make simple logical control decisions. The development of low cost computer has brought the most recent revolution, the Programmable Logic Controller (PLC),its a digital computer used for automation of electromechanical processes, such as control of machinery on factory assembly lines, amusement rides, or lighting fixtures,its act like a real time system since output results must be produced in response to input conditions within a bounded time

read more
Use Search at wisely To Get Information About Project Topic and Seminar ideas with report/source code along pdf and ppt presenaion
seminar flower
Super Moderator

Posts: 10,120
Joined: Apr 2012
25-07-2012, 04:56 PM

Programmable Logic Controllers

Program Control Instructions

Program control instructions are used to alter the program scan from its normal sequence. Sometimes referred to as override instructions, they provide a means of executing sections of the control logic if certain conditions are met. They allow for greater program flexibility and greater efficiency in the program scan.

Hardwired Master Control Relay Circuit

Hardwired master control relays are used in relay circuitry to provide input/output power shutdown of an entire circuit.

MCR Instruction

The master control reset (MCR) instruction can be programmed to control an entire circuit or to control only selected rungs of a circuit. When the MCR instruction is false, or de-energized, all nonretentive (nonlatched) rungs below the the MCR will be de-energized even if the programmed logic for each rung is true. All retentive rungs will remain in their last state. The MCR instruction establishes a zone in the user program in which all nonretentive outputs can be turned off simultaneously. Therefore, retentive instructions should not normally be placed within an MCR zone because the MCR zone maintains retentive instructions in the last active state when the instruction goes false.

Programming MCR Instructions

If you start instructions such as timers and counters
in an MCR zone, instruction operation ceases when the
zone is disabled.
The TOF timer will activate when placed inside a false
MCR zone.
When troubleshooting a program that contains an MCR zone you need to be aware of which rungs are within zones in order to correctly edit the circuit.
MCR controlled areas must contain only two MCR
instructions – one to define the start and one to define the end.

Jump Instruction

As in computer programming, it is sometimes desirable
to be able to jump over certain program instructions.
The jump instruction (JMP) is an output instruction used for this purpose. The advantages to the jump instruction include:
the ability to reduce the processor scan time by jumping over instructions not pertinent to the machines operation at that instant
The PLC can hold more than one program and scan only the program appropriate to operator requirements
Sections of a program can be jumped when a production fault occurs

Attached Files
.ppt   plc advance instruction.ppt (Size: 5.93 MB / Downloads: 18)

Important Note..!

If you are not satisfied with above reply ,..Please


So that we will collect data for you and will made reply to the request....OR try below "QUICK REPLY" box to add a reply to this page

Quick Reply
Type your reply to this message here.

Image Verification
Please enter the text contained within the image into the text box below it. This process is used to prevent automated spam bots.
Image Verification
(case insensitive)

Possibly Related Threads...
Thread Author Replies Views Last Post
  logic gate physics investigatory project in pdf Guest 1 89 31-10-2016, 11:20 AM
Last Post: anusree
  physics viva questions class 12 logic gates Guest 1 89 31-10-2016, 10:36 AM
Last Post: anusree
  investigatory project on physics class 12 on the topic logic gates doc download Guest 2 278 31-10-2016, 10:10 AM
Last Post: amrutha735
  physics viva questions class 12 logic gates Guest 1 96 29-10-2016, 04:34 PM
Last Post: amrutha735
  logic gates investigatory project for class12 cbse pdf file free download Guest 1 81 29-10-2016, 04:28 PM
Last Post: amrutha735
  physics viva questions class 12 logic gates Guest 1 84 29-10-2016, 03:45 PM
Last Post: amrutha735
  physics viva questions class 12 logic gates Guest 1 86 29-10-2016, 03:39 PM
Last Post: jaseela123
  logical form western and oriental conceptions of logic in research Guest 2 183 01-10-2016, 03:18 PM
Last Post: amrutha735
  aodv using fuzzy logic ns2 code Guest 1 220 14-04-2016, 12:59 AM
Last Post: fadhilmohammad2000
  programmable industrial on off timer with rf remote pdf Guest 2 113 15-03-2016, 02:12 PM
Last Post: mkaasees