smart card based door access system using LCD
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
shrey mathuria
Active In SP
**

Posts: 3
Joined: Oct 2010
#1
03-11-2010, 11:55 PM


I am shrey mathuria, pursuing bachelor studies in Electronics & Communication stream. I am working on the project and implimentation SMART CARD BASED DOOR ACCESS SYSTEM USING LCD and i am quite late in completing my project and implimentation according to college schedule, and its time to submit a 100 page report on this..including Abstract,block diagram and circuit diagram explanation,Future expansion,applications and advantages,drawbacks...can I get atleast some required information or data from you as per I have mentioned above regarding to my project and implimentation? coz i am not getting any detailed description or report like on my project and implimentation.
Reply
rathod parth
Active In SP
**

Posts: 1
Joined: Oct 2012
#2
07-10-2012, 01:36 PM

plz give me project and implimentation report on Smart Card Based Door Access System with lcd...................
Reply
seminar tips
Super Moderator
******

Posts: 8,857
Joined: Oct 2012
#3
08-10-2012, 12:29 PM

to get information about the topic "smart card based door access system using LCD" related topic refer the link bellow

seminar and presentationproject and implimentationsattachment.php?aid=5711
Reply
project girl
Moderator
*****

Posts: 10,114
Joined: Nov 2012
#4
17-11-2012, 11:20 AM

SMARTCARD BASED DOOR ACCESS SYSTEM USING LCD


.pptx   SMARTCARD BASED DOOR.pptx (Size: 238.23 KB / Downloads: 27)

INTRODUCTION

Here is the microcontroller-based Smartcard based door access system that can be used where accessing of door or any other electrical device, can open using a smart card on inserting the card user’s data is read by the microcontroller which will process the data the card is an EPROM IC.
The system is small, simple, cost-effective and good for smartcard based door. Smartcard is one of the latest additions to the world of information technology . It is connected to the LCD & KEYPAD. Smartcard may have up to 512 kb of EEPROM.Also this circuit operation is easily understand and easily runs circuit.

CIRCUIT DISCRIPTION

Whole project and implimentation can be divided into 7 blocks. They are:
 Power supply.
 Smartcard & smartcard Reader.
Microcontroller.
Switches.
 LCD interface.
 Buzzer interface.
 Relay interface.

16x2 LCD INTERFACE

Pin RC.0-to-RC.5 is connected with (16x2) LCD display. Microcontroller sends the data signals through pin no. RC.0-to-RC.3. this pin no. RC.0 to RC.3 is connected to pin no. 14 to11 of LCD display.
Control signal are send by microcontroller through pin no.RC.4 and RC.5 to LCD via pin no. 4 & 6 respectively. Pin no 3 of the LCD is used to control the contrast by using preset PR1.
Pin no. 1, 5 & 15 of LCD are normally connected to ground (GND). And pin no. 16 is normally connected to +5V (VCC) which supplies power to display.

BUZZER INTERFACE

Buzzer interface is used to audible indication for valid user and error situation and Alarm mode. A buzzer connected to the micro controller pin no. RC.7 via driver transistor BC547.
If we connect buzzer directly to pin no. RC.7 than buzzer will have input of only +5V at a current of around 0.6mA and to drive the buzzer it requires 12 volts at a current of around 50ma, which can’t be provided by the micro controller. So by keeping the driver transistor in common emitter configuration i.e. by connecting the pin no. RC.7 to base & buzzer to collector & another pin of buzzer to unregulated power supply of 12V (VDD) the buzzer can be operated.
 
Relay Interface

It is used for opening and closing of door. A Single-Pole-Double-Throw (SPDT) relay is connected to the micro controller pin no. RC.6 via driver transistor of BC547.
If we connect Relay directly to pin no. RC.6 than relay will have input of only +5V at a current of around 0.6mA and to drive the relay it requires 12 volts at a current of around 100ma, which can’t be provided by the micro controller. So by keeping the driver transistor in common emitter configuration i.e. by connecting the pin no. RC.6 to base & relay to collector & another pin of relay to unregulated power supply of 12V (VDD), the relay can be operated.
Now, when pin no. RC.6 pin will go high, the driver transistor will conduct and so current will flow from VDD to ground via LED L2 & so L2 LED will glow. And current will also flow from relay coil thus relay will operate.
Diode D6 is the standard diode on a 5 mechanical relay to prevent back EMF from damaging driver transistor Q2 when the relay releases it. LED L2 glow indicates that relay on.
Reply

Important Note..!

If you are not satisfied with above reply ,..Please

ASK HERE

So that we will collect data for you and will made reply to the request....OR try below "QUICK REPLY" box to add a reply to this page

Quick Reply
Message
Type your reply to this message here.


Image Verification
Please enter the text contained within the image into the text box below it. This process is used to prevent automated spam bots.
Image Verification
(case insensitive)

Possibly Related Threads...
Thread Author Replies Views Last Post
  Lightweight Directory Access Protocol Akshata Alegavi 3 619 22-09-2016, 03:45 PM
Last Post: Dhanabhagya
  density based traffic light ccontrole system Guest 0 539 18-09-2013, 10:21 AM
Last Post: Guest
  automated fault analysis system in industrly using gsm kunal rock 1 412 31-08-2013, 09:40 AM
Last Post: study tips
  renew of ration card Guest 0 1,095 25-08-2013, 07:36 PM
Last Post: Guest
  cloud computing for agent based urban transportation system Guest 2 1,624 10-08-2013, 03:39 PM
Last Post: study tips
  password based door locking system yasminmohammad 15 12,802 08-07-2013, 10:30 AM
Last Post: study tips
  documentation of RFID and ZIGBEE based manufacturing and monitoring system Guest 0 525 20-04-2013, 02:32 PM
Last Post: Guest
  isolated wind hydro hybrid system using cage generators and battery storage Guest 0 552 30-03-2013, 01:10 PM
Last Post: Guest
  phot bio centre in whitefield for ration card Guest 0 522 25-03-2013, 03:54 PM
Last Post: Guest
  weather monitoring system using micro controller namitha u 3 1,957 18-03-2013, 09:46 AM
Last Post: study tips