visnav full report
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
computer science technology
Active In SP
**

Posts: 740
Joined: Jan 2010
#1
22-01-2010, 04:08 PM



.doc   visnav full report.doc (Size: 793 KB / Downloads: 473)

ABSTRACT
Spacecraft missions such a spacecraft docking and formation flying requires high-precision relative position and attitude data. Although a global positioning system (GPS) can provide this capability near the earth, deep space missions require the use of alternative technologies. One such technology is the vision-based navigation (VISNAV) sensor system developed at Texas A&M university .J comprises an electro optical sensor combined with light sources or beacons. This patented sensor has an analog detector in the focal plane with a rise time of a few microseconds. Accuracies better than one part in 2000 of the field of view have been obtained .this paper presents a new approach involving simultaneous activation of beacons with frequency division multiplexing as part of the VISNA V sensor system.

INTRODUCTION
Now days there are several navigation systems for positioning the objects. Several research efforts have been carried out in the field of Six Degrees Of Freedom estimation for rendezvous and proximity operations. One such navigation system used in the field of Six Degrees Of Freedom position and attitude estimation is the VISion based NAVigation system. It is aimed at achieving better accuracies in Six Degrees Of Freedom estimation using a more simpler and robust approach.
The VISNAV system uses a Position Sensitive Diode (PSD) sensor for 6 DOF estimation. Output current from the PSD sensor determines the azimuth and elevation of the light source with respect to the sensor. By having four or more light source called beacons in the target frame at known positions the six degree of freedom data associated with the sensor is calculated.
The beacon channel separation and demodulation are done on a fixed point digital signal processor (DSP) Texas Instruments TMS320C55x [2] using digital down conversion, synchronous detection and multirate signal processing techniques. The demodulated sensor currents due to each beacon are communicated to a floating point DSP Texas Instruments TMS320VC33 [2] for subsequent navigation solution by the use of colinearity equations.

Among other competitive systems [3] a differential global positioning system (GPS) is limited to midrange accuracies, lower bandwidth, and requires complex infrastructures. The sensor systems based on differential GPS are also limited by geometric dilution of precision, multipath errors, receiver errors, etc.These limitations can be overcome by using the DSP embedded VISNAV system


SENSOR DESCRIPTION

Sensor geometry
We have discussed that Position Sensitive Diodes are used for sensing purpose. The Position Sensitive Diode (PSD) is a single substrate photodiode capable of finding or locating a light beam within defined sensing area. When photons meet the PSD sensor active area electrical currents are generated that flow through its four terminals. The closer the incident light centroid is to a particular terminal, the larger the position of current that flows through that load comparison of these four currents determines the centroid location of the incident light
With regards to the above figure the normalized voltage are as follows
Vy=k (Iright-Ileft) / (Iright+Ileft) (1)
Vz=k (Iup-Idown) / (Iup+Idown) (2)
Where K is a constant value 1 ohm.
This equation (1) is an indication of the angle the incident light beam makes about the object space X axis. Similarly equation (2) is determined by the angle that the incident light beam makes about the object space Y axis


FACTORS AFECTING MEASUREMENT
There is likely to be a large amount of ambient light at short wavelength and low carrier frequencies due to perhaps the sun, its reflections, incandescent or discharge tube lights, LCD and cathode ray tube displays etc. In many cases this ambient energy would swap a relatively small beacon signal and the PSD centroid data would mostly correspond to this unwanted background light.

In order to avoid this problem by modulating the beacon controller current by a sinusoidal carrier of high frequency. The resulting PSD signal currents then vary sinsuoidally at approximately the same frequency and have to be demodulated to recover the actual current proportional to the beacon light centroid. This modulation or demodulation scheme leads high degree of insensitivity to variations in ambient light and it is a key to make the PSD sensing approach practical.
Another method for solving this ambient light problem is that all energy except that centered on the colour wavelength of the beacon is greatly reduced by an optical colour filter. Another problem that affects the measurement is that high power beacon signal may saturate output of the preamplifier which is used after the PSD. So incident light centroid can not measure accurately. In order to avoid this problem a feedback control is used to hold the beacon light intensity at a level that results in a maximum PSD current at approximately 70% of the Tran impedance amplifier input saturation level.
SIGNAL PROCESSING

Block diagram of DSP embedded VISNAV system

This the general block diagram of VISNAV system. A sinusoidal carrier of approximately 40 kHz frequency is applied to modulate each beacon LED drive current. the resulting induced PSD signal current then vary sinusoidally at approximately same frequency and are demodulated to recover the currents that are proportional to the beacon light centroid.
The output of PSD is very weak. So we have to amplify these signals by using a preamplifier. After amplification this signal is fed to four channel analog to digital converter. This converts the four channels of analog data into digital form. And is then fed to the DSP, TMS320C55x [2] to demodulate the signal. After the demodulation the four channel data is fed to the Six Degree Of Freedom estimator, which uses DSP for estimation. From this point we get the sensor co-ordinates. As discussed earlier that the controlling of beacons to avoid the problem of saturation we uses the beacon control data which is given by the DSP, TMS320VC33 [2]. This control data is in digital form. We use radio link to communicate the control data from the sensor electronics module to the beacon controller module.
The beacon control data is then Frequency Shift Key (FSK) modulated. Then it is transmitted by using a wireless transmitter. The wireless receiver receives the control data and the beacon controller controls the amplitude or power level of beacons. This closed loop system estimates the Six Degree Of Freedom of the sensor.

MODULATION AND FREQUENCY DIVISION MULTIPLEXING
The PSDs are relatively fast compared to even high sped cameras, having rise time of about 5µs. this permits light sources to be structured in the frequency domain and utilization of radar-like signal processing methods to discriminate target energy in the presence of highly cluttered ambient optical scenes. If there is a single beacon excited by a sinusoidal oscillator operating at a frequency fc, the emitted light induces sinusoidal currents in the PSD with the frequency fc at the four terminals of the PSD sensor. Therefore, all the four currents can be processed in a similar fashion to estimate the amplitudes of the carrier waveforms. The amplitudes of these currents are related to the azimuth and elevation of the light source with respect to the image co-ordinate frame. If the PSD has a relative motion with respect to the beacon, the current envelopes are modulated by that relative motion and this modulation is analogous to amplitude modulation (AM). Thus the currents can be written as follows,
Ik(t) = (Ak.Cos(2 .pi .fc .t).(1+mk(t)))+nk _______________(3)
where k = 1,2,3, and 4 and it corresponds to the terminal number of the PSD, and Ak is the amplitude of the current waveform generated at the kth terminal of the PSD by the beacon that is fixed with respect to the PSD sensor. The function mk(t) denotes the signal envelope variation induced by the relative movement of the sensor. This is the case of single beacon operated at single frequency.
If there are multiple beacons operating at different frequencies, then the PSD terminal currents consists of current components at those frequencies, and can be written as follows,


Where N is the number of beacons and it should be greater than four for solving the 6 DOF inverse problem, Aj,k is the peak amplitude of the current generator at the kth terminal of the PSD corresponding to a light beam from jth beacon driven by a sinusoidal oscillator of frequency fj while the beacon is fixed with respect to the PSD sensor, mj,k(t) is the signal due to the relative movement of the sensor with respect to the jth beacon, and nj,k is the noise component due to the jth beacon at the kth terminal.
It is required to demodulate the above composite currents in real time for N*4 channels. The components to be recovered can thus be modeled as

rj,k(t)=Aj,k(1+mj,k(t)),j=1,2,3,.........,N; k=1,2,.......,4 ___(5)
It is worth pointing out that in normalized voltages, which are proportional to azimuth and elevation of the jth beacon with respect to the image co-ordinate frame, are obtained from the following relation similar to equation(1).
Vyj = k ((rj,1-rj,2) / (rj,1+rj,2))_________(6)
Vz,j = k ((rj,3-rj,4) / (rj,3+rj,4))_________(7)
The selection of frequencies for the beacons is based on several factors. The beacon frequency should ideally be above 20 kHz in order to distinguish it from lower frequency background ambient light that might include extraneous lighting sources. If the beacon frequency is too high, the PSD/pre amplifier noise will be greater. For practical purposes, the beacon frequency is selected to be near 40kHz. The separation between the beacon frequencies depends on the bandwidth of the beacon signal.

DEMODULATION
Considering that it is needed to determine the amplitude of the sinusoidal signal and the associated signal due to the relative movement of the sensor, an approach similar to AM demodulation is used here. The main difference, however, is that we are also interested in the carrier amplitude. Although analog circuits can be used to perform the channel separation and demodulation, the DSP based approach provides a more cost effective solution with a higher degree of reliability, programmability and scalability.
In the foregoing discussion, it is shown that for real implementation on a DSP processor, straight envelope detection is not feasible and the use of multirate signal processing can overcome this limitation. The PSD sensor generates four currents and a four channel synchronous analog to digital converter (ADC) samples these four currents. Each current contains the frequency components from around 48.25 to 52.25 kHz.
The sampling frequency of ADC is chosen as to be 210 kHz, which is four times the anticipated maximum frequency component of nearest or 52.5 kHz. Four pre amplifiers with unity gain in the range of 48.25 kHz to 52.25 kHz together with a gradual attenuation at other frequencies are used to supply the currents to the ADC. This attenuation reaches 80dB at higher frequencies around 105 kHz and also at lower frequencies near 0 Hz. The word length is chosen to be 12 bits.
Since all the four PSD currents are similar in terms of frequency components, the beacon channel separation and demodulation methods are common to all of them. Bandpass filtering for the selection of the beacon channel and then envelope detection consisting of rectification and lowpass filtering are performed. Since the beacon carrier frequencies are separated by 500 Hz, the bandpass filter is designed to have a unity gain passband from fj-100 to fj+100 Hz, a transition bandwidth of 150 Hz from fj-250 to fj-100 and from fj+100 to fj+250. The stopband attenuation is around 80dB. The demodulation can be done by implementing algorithms on DSP.


DSP IMPLIMENTATION
The beacons are multiplexed in FDM mode. A low power fixed point DSP, TMS320C55x [2] is utilized for the algorithm of beacon separation and demodulation. Asynchronous analog to digital converter samples the sensorâ„¢s four currents to feed estimates to the TMS320C55x [2]. Each current has frequency components corresponding to the frequencies of different beacons. For the case of eight beacons the carrier frequencies are starting from 48.5 kHz with an interchannel separation of 0.5 kHz, in order to distinguish from low frequency background noise.
TMS320C55x communicates the demodulated beacon currents to the TMS320VC33 for subsequent navigation solution. The TMS320VC33 [2] estimates the Six Degree Of Freedom position and attitude according to the beacon currents. The algorithm for the Six Degree Of Freedom estimation is implemented on this processor. It also provides feedback control signals to the beacon controller.

ADVANTAGES
¢ It can be easily reprogrammed
¢ Insensitive to temperature variations and ageing effects
¢ It is easily scaled up to 16 beacons with slight modifications in the software.
¢ It has small size.
¢ It has wide sensor field of view.
¢ It has no time consuming image processing employed.
DISADVANTAGES
¢ The signals may be blocked by opaque objects in their paths.
APPLICATIONS
VISNAV system has a wide range of applications. Two of them are as follows
1. Aerial refueling
2. Spacecraft docking
AERIAL REFUELING
The aim this application is to extend the operational envelop of unmanned aerial vehicles by designing an autonomous in flight refueling system. One of the most difficult technical problems in autonomous flight refueling is the accuracy. That is it needs high accurate sensor to measure the location of the tanker and the aircraft. Currently Global Positioning System (GPS) is limited by an accuracy of one foot approximately.
The VISNAV system is capable of providing the needed Six Degree Of Freedom information for real time navigation and can enable accurate autonomous aerial refueling without extensive alterations in the current refueling system.

In order to implement VISNAV system the only thing that is to attach the light sources called beacons on the refueling target frame ËœAâ„¢ and an optical sensor called Position Sensitive Diode (PSD) on the aircraft frame ËœBâ„¢. The aerial refueling using VISNAV can be used in the 100% of cloud cover, total darkness and adverse weather conditions.

SPACECRAFT DOCKING


Spacecraft docking
This is one of the applications of VISNAV system. In the figure docking point of two spacecraft is shown. The active beacons are placed in one of the docking surface. The beacon controller part is also placed in the same surface. Some beacons are placed near the docking point and some are placed wide apart. This is to provide a wide range of field of view.
The sensor part consists of a PSD sensor which is placed on the other aircraft near the docking point. A beam of light is transmitted from the docking point of the other spacecraft. The sensor senses this light from the spacecraft and is then converted into four currents, whose imbalance is used to find out the centroid of the light. The centroid will give the Six Degree Of Freedom of the spacecraft.

CONCLUSION
A new method for operating beacons and demodulating the beacon currents for the VISNAV sensor system is introduced here. It is shown that target differentiation based on FDM yields higher signal to noise ratios for the sensor measurements and the demodulation in the digital domain using multirate signal processing techniques brings reliability and flexibility to the sensor system. The algorithm that is implemented on DSP is robust when there are four or more of line of sight measurements except near certain geometric conditions that are rarely encountered. It is shown that this algorithm is computationally efficient and achieves better results.
BIBLIOGRAPHY
1. Kiran K. Gunnam, Declan C.Hughes, John L Junkins, and Nasser Kehtamavaz, A Vision Based DSP Embedded Navigation Sensor.IEEE Sensors journal, Vol 2, NO: 5,October 2002
2. dspvillage.ti.com
3. gpsworld.com
4. Thyagarajan, Electronic navigation systems
5. jungfrau.tamu.edu/~html/visionlab

CONTENTS
1 INTRODUCTION 1
2 SENSOR DESCRIPTION 3
3 FACTORS AFFECTING MEASUREMENT 5
4 SIGNAL PROCESSING 6
5 MODULATION AND FREQUENCY DIVISION MULTIPLEXING 8
6 DEMODULATION 11
7 DSP IMPLEMENTATION 13
8 ADVANTAGES & DISADVANTAGES 14
9 APPLICATIONS 15
9.1 AERIAL REFUELING 15
9.2 SPACECRAFT DOCKING 16
10 CONCLUSION 17
11 BIBLIOGRAPHY 18
ACKNOWLEDGEMENT
I extend my sincere gratitude towards Prof. P. Sukumaran Head of Department for giving us his invaluable knowledge and wonderful technical guidance
I express my thanks to Mr. Muhammed Kutty our group tutor and also to our staff advisor Ms. Biji Paul for their kind co-operation and guidance for preparing and presenting this seminar and presentation.
I also thank all the other faculty members of AEI department and my friends for their help and support.
Use Search at http://topicideas.net/search.php wisely To Get Information About Project Topic and Seminar ideas with report/source code along pdf and ppt presenaion
Reply
seminar class
Active In SP
**

Posts: 5,361
Joined: Feb 2011
#2
23-02-2011, 12:22 PM


.pdf   VISNAV.pdf (Size: 82.08 KB / Downloads: 179)
INTRODUCTION
Now days there are several navigation systems for positioning
the objects. Several research efforts have been carried out in the field of
Six Degrees Of Freedom estimation for rendezvous and proximity
operations. One such navigation system used in the field of Six Degrees
Of Freedom position and attitude estimation is the VISion based
NAVigation system. It is aimed at achieving better accuracies in Six
Degrees Of Freedom estimation using a more simpler and robust
approach.
The VISNAV system uses a Position Sensitive Diode (PSD)
sensor for 6 DOF estimation. Output current from the PSD sensor
determines the azimuth and elevation of the light source with respect to
the sensor. By having four or more light source called beacons in the
target frame at known positions the six degree of freedom data associated
with the sensor is calculated.
The beacon channel separation and demodulation are done on a
fixed point digital signal processor (DSP) Texas Instruments
TMS320C55x [2] using digital down conversion, synchronous detection
and multirate signal processing techniques. The demodulated sensor
currents due to each beacon are communicated to a floating point DSP
Texas Instruments TMS320VC33 [2] for subsequent navigation solution
by the use of colinearity equations.
Among other competitive systems [3] a differential global
positioning system (GPS) is limited to midrange accuracies, lower
bandwidth, and requires complex infrastructures. The sensor systems
based on differential GPS are also limited by geometric dilution of
precision, multipath errors, receiver errors, etc.These limitations can be
overcome by using the DSP embedded VISNAV system
Sensor geometry
We have discussed that Position Sensitive Diodes are used for
sensing purpose. The Position Sensitive Diode (PSD) is a single substrate
photodiode capable of finding or locating a light beam within defined
sensing area. When photons meet the PSD sensor active area electrical
currents are generated that flow through its four terminals. The closer
the incident light centroid is to a particular terminal, the larger the
position of current that flows through that load comparison of these four
currents determines the centroid location of the incident light
With regards to the above figure the normalized voltage are as
follows
Vy=k (Iright-Ileft) / (Iright+Ileft) 8(1)
Vz=k (Iup-Idown) / (Iup+Idown) 8(2)
Visnav
Where K is a constant value 1 ohm.
This equation (1) is an indication of the angle the incident light
beam makes about the object space X axis. Similarly equation (2) is
determined by the angle that the incident light beam makes about the
object space Y axis
Reply
seminar class
Active In SP
**

Posts: 5,361
Joined: Feb 2011
#3
21-03-2011, 09:25 AM

Submitted by
Ajesh.M.L


.pptx   ajesh.m.l.pptx (Size: 792.92 KB / Downloads: 188)
Introduction
Objectives

1. Find 6 DOF estimation
2. Find Robust Navigation Solution
 Consist of PSD & DSP
Limitations of GPS
1. Less Precision
2. Complex infrastructure
3. Low accuracy
Sensor Description
 Activated by energy from beacons
 Generates electrical current in 4 directions
 Current imbalances are linearly proportional to location of image centroid
Factors affecting measurement
 Short wavelength light from sun & other discharge light act as beacons
 High power beacon signal saturate output of preamplifier
Preventive Measures
 Optical filter to block visible light.
 Modulate beacon current with high frequency.
 Feed back loop to control the beacon intensity.
VISNAV Block Diagram
Signal Processing

• Sinusoidal carrier of 40kHz frequency applied to modulate each drive current from the four terminals of the PSD.
• The output of the PSD is applied to the preamplifier
• The signal is converted into digital form through an analog to digital converter.
• The digital data fed into the two DSP’s from this we get a sensor coordinates.
• Beacon control data is communicated to BCM.
• Control data is FSK modulated
• Data then transmitted via wireless link to control amplitude of beacons.
• This closed loop system estimates 6 DOF of sensor.
DSP Implementation
 Functions of DSP TMS320C55X-act as demodulator
 Functions of DSP TMS320VC33 act as 6 DOF estimator
ADVANTAGES
 Reprogrammable
 Insensitive to temperature variation and ageing effect
 Wide field of view
 Very small and compact size
 Number can be increased upto 16 beacons
DISADVANTAGE
 The signal may be blocked by the opaque objects in their path
Applications
1. Autonomous aerial refuelling.
• Aerial Refuelling
 Requires light sources on the refuelling target frame
 optical sensor on the aircraft frame.
 Can be used even in 100% cloud cover,total darkness and adverse condition
2. Spacecraft Docking
 Beacons & beacon contoller on target spacecraft & sensor on chasing space craft
 VISNAV enables docking simple and easy
Conclusions
 100 Hz update rate 6DOF data possible with small low power sensor/beacons to 100+m.
 Beacon signal modulation and optical filtering
 Excellent ambient light rejection.
 Realtime beacon selection/intensity control
 Minimize power requirements.
 Very wide field of view, no moving parts.
 Distributed beacons
 Very large operating space
Reply
seminar addict
Super Moderator
******

Posts: 6,592
Joined: Jul 2011
#4
30-01-2012, 11:34 AM

to get information about the topic visnav full report, ppt and related topic refer the link bellow
topicideashow-to-visnav-full-report

topicideashow-to-visnav--2335

topicideashow-to-visnav--19816

Reply

Important Note..!

If you are not satisfied with above reply ,..Please

ASK HERE

So that we will collect data for you and will made reply to the request....OR try below "QUICK REPLY" box to add a reply to this page

Quick Reply
Message
Type your reply to this message here.


Image Verification
Please enter the text contained within the image into the text box below it. This process is used to prevent automated spam bots.
Image Verification
(case insensitive)

Possibly Related Threads...
Thread Author Replies Views Last Post
  digital image processing full report computer science technology 40 47,780 08-03-2014, 12:52 PM
Last Post: aumsree
  solar power satellite full report computer science technology 30 33,680 28-02-2014, 07:01 PM
Last Post: sandhyaswt16
  electronic nose full report project report tiger 15 17,851 24-10-2013, 11:23 AM
Last Post: Guest
  smart pixel arrays full report computer science technology 5 8,105 30-07-2013, 05:10 PM
Last Post: Guest
  smart antenna full report computer science technology 18 22,596 25-07-2013, 01:55 PM
Last Post: livon
  speed detection of moving vehicle using speed cameras full report computer science technology 14 22,669 19-07-2013, 04:40 PM
Last Post: study tips
  speech recognition full report computer science technology 17 22,854 14-05-2013, 12:28 PM
Last Post: study tips
  global system for mobile communication full report computer science technology 9 8,522 06-02-2013, 10:01 AM
Last Post: seminar tips
  satrack full report computer science technology 10 17,505 02-02-2013, 10:53 AM
Last Post: seminar tips
  Wireless Battery Charger Chip for Smart-Card Applications full report project topics 8 7,576 28-01-2013, 03:02 PM
Last Post: varna prasad